Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Combination Meter or Main Body / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Combination Meter (Combination Meter Assembly) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Seatbelt Buckle SW
    Front passenger side seat belt buckle switch signal/ON or OFF
    ON: Front passenger side seat belt fastened.
    OFF: Front passenger side seat belt not fastened.
    -
    2nd-Row Seatbelt Buckle (R)*
    Rear RH side seat belt buckle switch signal/ON or OFF
    ON: Rear RH side seat belt fastened.
    OFF: Rear RH side seat belt unfastened.
    -
    2nd-Row Seatbelt Buckle (L)*
    Rear LH side seat belt buckle switch signal/ON or OFF
    ON: Rear LH side seat belt fastened.
    OFF: Rear LH side seat belt unfastened.
    -
    2nd-Row Seatbelt Buckle (C)*
    Rear center seat belt buckle switch signal/ON or OFF
    ON: Rear center seat belt fastened.
    OFF: Rear center seat belt unfastened.
    -
    Driver Side Seatbelt Warning Buzzer
    Driver side seat belt warning buzzer/ON or OFF
    Customized value displayed
    -
    P-Seatbelt Warning Buzzer
    Front passenger side seat belt warning buzzer/ON or OFF
    Customized value displayed
    -
    Rear Seat Belt Warning Buzzer*
    Rear seat belt warning buzzer/OFF or ON
    Customized value displayed
    -
    *: w/ Rear Seat Belt Warning

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door Courtesy SW
    Rear door courtesy switch signal/ON or OFF
    ON: Rear door LH or RH open.
    OFF: Rear door LH and RH closed.
    -
    RL Door Courtesy SW
    Rear door courtesy switch signal/ON or OFF
    ON: Rear door LH or RH open.
    OFF: Rear door LH and RH closed.
    -
    D Seat Buckle SW
    Driver seat belt buckle switch signal/ON or OFF
    ON: Driver seat belt fastened
    OFF: Driver seat belt not fastened
    -


ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Combination Meter / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Combination Meter (Combination Meter Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver side seat belt warning light
    OFF or ON
    Confirm that the vehicle is stopped with the engine idling.
    Front Passenger Side Seat Belt
    Front passenger side seat belt warning light
    OFF or ON
    Confirm that the vehicle is stopped with the engine idling.