Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Instrument Panel Illumination Circuit

for Preparation Click here


DESCRIPTION

  1. When the taillights are turned on by the automatic light control or manual light control, the instrument panel illumination is also turned on.
  2. When the taillights are turned on by the daytime running light control, the instrument panel illumination ON is prohibited.

WIRING DIAGRAM


E183406E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester tester to the DLC3.

  1. Turn power switch on (IG).

  1. Turn the intelligent tester tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Check that the relay operate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Interior Panel Relay
    Interior panel relay
    ON/OFF
    Power switch is off and light control switch in tail position.

    OK:
    Relay operates (each light comes on or off).



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT INSTRUMENT PANEL ILLUMINATION RELAY (PANEL)


    B060778E87
  1. Remove the PANEL relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL ILLUMINATION RELAY
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY - PANEL RELAY)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 1 - Body ground
    Light control switch off → tail
    Below 1 V → 11 to 14 V
    Relay terminal 3 - Body ground
    Light control switch off → tail
    Below 1 V → 11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (PANEL RELAY - MAIN BODY ECU)
  1. Disconnect the L7 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 2 - L7-15 (PANL)
    Always
    Below 1 Ω
    L7-15 (PANL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    E166535E03
  1. Reconnect the L7 main body ECU (multiplex network body ECU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L7-15 (PANL) - Body ground
    Light control switch in tail
    Below 1 V
    Light control switch in AUTO and taillights are on
    Below 1 V
    Taillights are turned on by the daytime running light control
    11 to 14 V

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU (Multiplex Network Body ECU))



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RELAY - EACH INSTRUMENT PANEL ILLUMINATION)