Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY


  1. Disconnect the L27 combination meter assembly connector.


    B129553E04

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-24 (SW) - Body ground
    P - Body ground
    Front passenger side seat belt buckle switch signal
    Front passenger side seat occupied, seat belt fastened
    10 kΩ or higher
    L27-24 (SW) - Body ground
    P - Body ground
    Front passenger side seat belt buckle switch signal
    Front passenger side seat occupied, seat belt unfastened
    Below 1 Ω
    L27-32 (RRSB) - Body ground*
    R - Body ground
    Rear RH side seat belt buckle switch signal
    Rear RH side seat belt fastened
    10 kΩ or higher
    L27-32 (RRSB) - Body ground*
    R - Body ground
    Rear RH side seat belt buckle switch signal
    Rear RH side seat belt unfastened
    Below 1 Ω
    L27-33 (RCSB) - Body ground*
    L - Body ground
    Rear center seat belt buckle switch signal
    Rear center seat belt fastened
    10 kΩ or higher
    L27-33 (RCSB) - Body ground*
    L - Body ground
    Rear center seat belt buckle switch signal
    Rear center seat belt unfastened
    Below 1 Ω
    L27-34 (RLSB) - Body ground*
    Y - Body ground
    Rear LH side seat belt buckle switch signal
    Rear LH side seat belt fastened
    10 kΩ or higher
    L27-34 (RLSB) - Body ground*
    Y - Body ground
    Rear LH side seat belt buckle switch signal
    Rear LH side seat belt unfastened
    Below 1 Ω
    L27-30 (ES) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    *: w/ Rear Seat Belt Warning
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L27 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F27-19 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch off
    Below 1 V
    F27-19 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    F27-21 (PBLT) - Body ground
    Y - Body ground
    Front passenger side seat belt warning light signal
    Power switch on (IG), front passenger side seat occupied, seat belt fastened
    11 to 14 V
    F27-21 (PBLT) - Body ground
    Y - Body ground
    Front passenger side seat belt warning light signal
    Power switch on (IG), front passenger side seat occupied, seat belt unfastened
    Alternates between 11 to 14 V and below 1 V
    If the result is not as specified, the combination meter assembly may have a malfunction.


PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY

B230278E01

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-6 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    M2-6 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch off
    Below 1 V
    M2-3 (PBEW) - Body ground
    W - Body ground
    Front passenger side seat belt warning light signal
    Front passenger side seat occupied, seat belt fastened
    11 to 14 V
    M2-3 (PBEW) - Body ground
    W - Body ground
    Front passenger side seat belt warning light signal
    Front passenger side seat occupied, seat belt unfastened
    Alternates between 11 to 14 V and below 1 V

    1. If the result is not as specified, the passenger seat belt warning light assembly may have a malfunction.


MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B230102E06

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch input
    Rear door LH or RH open
    Below 1 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch input
    Rear door LH and RH closed
    11 to 14 V
    2B-14 (DBKL) - Body ground
    P - Body ground
    Driver side seat belt buckle
    Driver side seat belt fastened
    Below 1 V
    2B-14 (DBKL) - Body ground
    P - Body ground
    Driver side seat belt buckle
    Driver side seat belt unfastened
    11 to 14 V
    If the result is not as specified, the main body ECU (multiplex network body ECU) may have a malfunction.