Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR

OUTER REAR VIEW MIRROR > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


  1. Inspect the operation of the mirror surface.



      B225734E01
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      Turns upward
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      Turns downward
      Battery positive (+) → Terminal 4 (MH)
      Battery negative (-) → Terminal 5 (M+)
      Turns left
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.

  1. Check the mirror heater (w/ Mirror heater).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 1 (HL-) - Terminal 2 (HL+)
      25°C (77°F)
      7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly.



2. INSPECT OUTER MIRROR RETRACTOR LH


  1. Inspect the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.




      B199933E11
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:
      Tester Connection
      Condition
      Specified Condition
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      Text in Illustration 
      *1
      (A) Forward Position
      *2
      (B)
      *3
      (C) Driving position
      *4
      (D)
      *5
      (E) Retracted Position
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


  1. Inspect the operation of the mirror surface.



      B225733E01
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      Turns upward
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      Turns downward
      Battery positive (+) → Terminal 4 (MH)
      Battery negative (-) → Terminal 5 (M+)
      Turns left
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.

  1. Check the mirror heater (w/ Mirror heater).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 1 (HR-) - Terminal 2 (HR+)
      25°C (77°F)
      7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly.



4. INSPECT OUTER MIRROR RETRACTOR RH


  1. Inspect the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.




      B199932E12
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:
      Tester Connection
      Condition
      Specified Condition
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 11 (MR)
      Battery negative (-) → Terminal 10 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 10 (MF)
      Battery negative (-) → Terminal 11 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      Text in Illustration 
      *1
      (A) Forward Position
      *2
      (B)
      *3
      (C) Driving position
      *4
      (D)
      *5
      (E) Retracted Position
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.