Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15C2    Speed Signal Malfunction

for Preparation Click here


DESCRIPTION

The navigation ECU sub-assembly receives a vehicle speed signal from the No. 3 meter circuit plate and information from the navigation antenna assembly, and then adjusts the vehicle position.
The navigation ECU sub-assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the No. 3 meter circuit plate becomes large.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the No. 3 meter circuit plate. The signal is changed to a pulse signal at the transistor in the No. 3 meter circuit plate. Each ECU controls the respective systems based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.


DTC No.
DTC Detection Condition
Trouble Area
B15C2
A difference between the GPS speed and SPD pulse is detected.
  1. Navigation ECU sub-assembly
  2. No. 3 meter circuit plate
  3. Harness or connector
  4. Junction connector

WIRING DIAGRAM


E237359E01


INSPECTION PROCEDURE

1.CHECK VEHICLE SENSOR (OPERATION CHECK)


    E176549
  1. Enter the "Vehicle Sensors" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (Click here).

  1. While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

    HINT:
    The No. 3 meter circuit plate receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

    OK:
    Vehicle speed displayed on the "Vehicle Sensors" screen is almost the same as the actual vehicle speed measured using the intelligent tester (Click here).



NG
Go to step 2
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

2.INSPECT NO. 3 METER CIRCUIT PLATE (OUTPUT WAVEFORM)


    E210226E10
  1. Check the output waveform.

    1. Remove the No. 3 meter circuit plate with the connector(s) still connected.

    2. Connect an oscilloscope to terminal L27-7 (+S) and body ground.

    3. Turn the power switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Measurement terminal
      L27-7 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *a
      Component with harness connected
      (No. 3 Meter Circuit Plate)



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


3.INSPECT NAVIGATION ECU SUB-ASSEMBLY (INPUT WAVEFORM)


    E240144E02
  1. Check the input waveform.

    1. Remove the navigation ECU sub-assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal L130-17 (SPD) and body ground.

    3. Turn the power switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Measurement terminal
      L130-17 (SPD) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *a
      Component with harness connected
      (Navigation ECU Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - NO. 3 METER CIRCUIT PLATE)
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)