BACK DOOR GLASS > REMOVAL |
| 1. REMOVE UPPER BACK DOOR TRIM PANEL ASSEMBLY |
![]() |
Using a moulding remover, disengage the 4 clips and 4 claws, and remove the upper back door trim panel assembly.
| 2. REMOVE BACK DOOR SIDE GARNISH RH |
![]() |
Disengage the 3 clips and 2 claws, and remove the back door side garnish RH.
| 3. REMOVE BACK DOOR SIDE GARNISH LH |
![]() |
Disengage the 3 clips and 2 claws, and remove the back door side garnish LH.
| 4. REMOVE BACK DOOR TRIM BOARD ASSEMBLY |
![]() |
Using a moulding remover, disengage the clip and claw.
![]() |
Using a moulding remover, disengage the clip and claw.
![]() |
Disengage the 3 clips in the order shown in the illustration.
![]() |
Disengage the 2 clips by pulling the back door trim board assembly in the direction indicated by the arrows in the illustration.
![]() |
Remove the back door trim board assembly by pulling it in the direction indicated by the arrow in the illustration to disengage the 4 clips.
| *1 | Back Door Trim Board Assembly |
| *2 | Back Door Panel |
| *a | The portion that may be damaged due to interference |
| 5. REMOVE BACK DOOR TRIM BOARD |
![]() |
Disengage the 5 clips and 2 guides, and remove the back door trim board.
| 6. REMOVE REAR SPOILER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 5 nuts.
![]() |
Disengage the 2 clips to remove the rear spoiler assembly.
| 7. REMOVE REAR WIPER ARM HEAD CAP (w/ Resin Wiper Arm) |
for Back Door Glass:
Remove the rear wiper arm head cap .
| 8. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY |
for Back Door Glass:
Remove the rear wiper arm and blade assembly .
| 9. REMOVE REAR WIPER MOTOR GROMMET |
for Back Door Glass:
Remove the rear wiper motor grommet .
| 10. REMOVE REAR WIPER MOTOR ASSEMBLY |
for Back Door Glass:
Remove the rear wiper motor assembly .
| 11. REMOVE BACK DOOR GLASS |
w/o Glass Breakage Sensor:
![]() |
Disconnect the 2 connectors.
w/ Glass Breakage Sensor:
![]() |
Disconnect the 4 connectors.
![]() |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
| *1 | Protective Tape |
![]() |
Pass a piano wire between the vehicle body and back door glass from the interior, as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the back door glass.
![]() |
Using suction cups, disengage the 2 clips and remove the back door glass.
| 12. REMOVE NO. 1 BACK DOOR GLASS ADHESIVE DAM |
![]() |
Remove the No. 1 back door glass adhesive dam.
| 13. REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING LH |
![]() |
Remove the No. 1 back window outside moulding LH.
| *1 | LH Side |
| *2 | RH Side |
| 14. REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING RH |
| 15. REMOVE NO. 1 BACK WINDOW LOWER MOULDING |
![]() |
Remove the No. 1 back window lower moulding.
| 16. REMOVE NO. 2 BACK WINDOW GLASS SPACER |
![]() |
Using a scraper, remove the No. 2 back window glass spacer.
| *1 | No. 2 Back Window Glass Spacer |
| *2 | No. 1 Back Window Glass Spacer |
| 17. REMOVE NO. 1 BACK WINDOW GLASS SPACER |
| 18. CLEAN BACK DOOR GLASS |
![]() |
Clean the outer edge of the back door glass with a non-residue solvent.
| 19. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY |
for Back Door Window Fix Glass:
Remove the back door outside garnish sub-assembly .
| 20. REMOVE BACK WINDOW FIX GLASS |
w/o Glass Breakage Sensor:
![]() |
Disconnect the 2 connectors.
w/ Glass Breakage Sensor:
![]() |
Disconnect the 3 connectors.
![]() |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
| *1 | Protective Tape |
![]() |
Pass a piano wire between the vehicle body and back window fix glass from the interior, as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the back door glass.
![]() |
Using suction cups, disengage the 2 clips and remove the back door glass.
| 21. REMOVE NO. 2 BACK DOOR GLASS ADHESIVE DAM |
![]() |
Using a scraper, remove the back door glass adhesive dam.
| 22. REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING LH |
![]() |
Using a scraper, remove the NO. 2 back window outside moulding LH.
| *1 | LH Side |
| *2 | RH Side |
| 23. REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING RH |
| 24. REMOVE NO. 2 BACK WINDOW LOWER MOULDING |
![]() |
Using a scraper, remove the back window lower moulding.
| 25. REMOVE NO. 2 BACK DOOR GLASS SPACER |
![]() |
Using a scraper, remove the No. 2 back door glass spacer.
| *1 | No. 2 Back Window Glass Spacer |
| *2 | No. 1 Back Window Glass Spacer |
| 26. REMOVE NO. 1 BACK DOOR GLASS SPACER |
| 27. CLEAN BACK WINDOW FIX GLASS |
![]() |
Clean the outer edge of the back window fix glass with a non-residue solvent.
| 28. CLEAN VEHICLE BODY |
![]() |
Using a scraper, remove the moulding and adhesive from the back window fix glass.
| *1 | Adhesive |
| *2 | Vehicle Body |
Clean and shape the contact surfaces of the vehicle body.
Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.
Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.