Home › Brake › BRAKE (REAR) › REAR BRAKE

REAR BRAKE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL REAR DISC


    C151123E03
  1. Align the matchmarks of the disc and axle hub, and install the disc.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



2. INSTALL REAR DISC BRAKE CYLINDER MOUNTING


    C108950
  1. Install the rear disc brake cylinder mounting to the axle beam with the 2 bolts.

    Torque:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }



3. INSTALL REAR DISC BRAKE BUSHING DUST BOOT


    C208163E01
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



    C108949
  1. Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.



4. INSTALL REAR DISC BRAKE PAD GUIDE PIN


    C190382E01
  1. Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the 2 rear disc brake pad guide pins.



    C132250
  1. Install the 2 rear disc brake pad guide pins to the rear disc brake cylinder mounting.



5. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE


    C205526
  1. Install the 2 rear disc brake pad support plates to the rear disc brake cylinder mounting.

    NOTICE:
    Be sure to install each rear disc brake pad support plate in the correct position and direction.



6. INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM


    C276190
  1. Apply disc brake grease to the back plate of the rear disc brake pads.
    Text in Illustration 
    V100145
    Disc Brake Grease



    C208164E01
  1. Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.
    Text in Illustration 
    *1
    Rear No. 1 Disc Brake Anti-squeal Shim
    *2
    Rear No. 2 Disc Brake Anti-squeal Shim

    NOTICE:
    1. When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
    2. Apply disc brake grease to the area that contacts the anti-squeal shim.
    3. Disc brake grease may seep out slightly from the areas where the anti-squeal shims are installed.
    4. Make sure that disc brake grease is not applied onto the lining surface.



7. INSTALL REAR DISC BRAKE PAD


    C152378
  1. Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



    C205528
  1. Install the 2 anti-squeal springs to the rear disc brake pads.

    NOTICE:
    1. When replacing the rear disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.
    2. Be sure to install the anti-squeal springs into the rear disc brake pad installation holes as far as they will go.



8. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY


    C108962E01
  1. To compensate for pad wear when reusing the pad, use SST to turn the piston to the position where the protrusion on the pad lines up properly with the piston groove.
    Retract
    Extend
    Clockwise
    Counterclockwise

    SST
    09960-10010   (09963-00400)

    NOTICE:
    Place the disc between the 2 brake pads and determine the piston return value.



    C151108E02
  1. Hold the rear disc brake cylinder pad guide pin, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.
    Text in Illustration 
    *1
    Hold
    *2
    Turn

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }

    NOTICE:
    1. Install the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads.
    2. Be sure that the anti-squeal springs are installed to the rear disc brake pads.



9. CONNECT REAR FLEXIBLE HOSE


    C151107
  1. Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



10. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C155547E03
  1. Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    No. 3 Parking Brake Cable Assembly
    *2
    Clip

    HINT:
    Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.



    C155545E02
  1. Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.



11. FILL RESERVOIR WITH BRAKE FLUID


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Perform the following procedure if air bleeding is not necessary:

    1. Connect the reservoir level switch connector.

    2. Clear the DTCs (Click here).



13. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



14. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



15. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



16. BLEED BRAKE LINE


  1. Remove the center cowl top ventilator cover.



      C205662
    1. Slide the hood to cowl top seal and disengage the claw.

    2. Disengage the 2 claws and 3 guides, and remove the center cowl top ventilator cover.



  1. Bleed brake line.



      C205665
    1. Remove the brake master cylinder reservoir filler cap assembly.

    2. Add brake fluid into the reservoir between MAX and MIN level on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    4. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    5. Select the "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

    6. After air bleeding, tighten each bleeder plug.

      Torque:
      front bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      rear bleeder plug:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Clear the DTCs (Click here).

    8. Turn the intelligent tester off and turn the power switch off.

  1. Inspect for brake fluid leaks.

  1. Install the brake master cylinder reservoir filler cap.



  1. Install the center cowl top ventilator cover.



      C205663
    1. Engage the 2 claws and 3 guides to install the center cowl top ventilator cover.

    2. Slide the hood to cowl top seal to engage the claw.



17. ADJUST PARKING BRAKE

HINT:
Click here



18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)
  1. Connect each connector.

  1. Engage the clamp.

  1. Engage the 2 guides and claw to connect the hood lock control cable.



    B298864
  1. Engage the 6 claws and clip.

  1. Install the lower instrument panel finish panel assembly with the screw <C>.



19. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    B227764
  1. Engage the 2 clips.

  1. Install the cowl side trim board LH with the clip.



20. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)


    B227761
  1. Engage the 10 claws to install the front door scuff plate LH.



21. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
  1. Connect each connector.

  1. Engage the guide and 2 claws.

  1. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.



22. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }