Home › Brake › BRAKE (REAR) › REAR BRAKE

REAR BRAKE > REMOVAL

for Preparation Click here


NOTICE:
  1. When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
  2. While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and setting. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C205666
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE REAR WHEEL


7. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.



8. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    B227761
  1. Disengage the 10 claws and remove the front door scuff plate LH.



9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    B227764
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


    B223460
  1. Remove the screw <C>.



    B223461
  1. Disengage the 6 claws and clip as shown in the illustration.



    B223463
  1. Disengage the claw and 2 guides and disconnect the hood lock control cable.

  1. Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.



11. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    B223634
  1. Remove the screw <D>.

  1. Disengage the 2 claws and guide.

  1. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.



12. LOOSEN PARKING BRAKE CABLE
  1. Completely release the parking brake pedal.



    C206641E01
  1. Loosen the lock nut and adjusting nut to completely release the parking brake cable.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut



13. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C155545E01
  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



    C155546E03
  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    No. 3 Parking Brake Cable Assembly
    *2
    Clip
    *3
    Offset Wrench (14 mm)

    HINT:
    Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



14. SEPARATE REAR FLEXIBLE HOSE


    C151107
  1. Remove the union bolt and gasket, and separate the rear flexible hose from the rear disc brake cylinder assembly.



15. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY


    C151108E02
  1. Hold the rear disc brake pad guide pin, and remove the 2 bolts and rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    Hold
    *2
    Turn

    NOTICE:
    Remove the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads.



16. REMOVE REAR DISC BRAKE PAD


    C205527
  1. Remove the 2 anti-squeal springs from the rear disc brake pads.

  1. Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.



17. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM


    C208164E01
  1. Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.
    Text in Illustration 
    *1
    Rear No. 1 Disc Brake Anti-squeal Shim
    *2
    Rear No. 2 Disc Brake Anti-squeal Shim



18. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE


    C125280
  1. Remove the 2 rear disc brake pad support plates from the disc brake cylinder mounting.

    NOTICE:
    Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be installed to its original position.



19. REMOVE REAR DISC BRAKE PAD GUIDE PIN


    C132250
  1. Remove the 2 rear disc brake pad guide pins from the rear disc brake cylinder mounting.



20. REMOVE REAR DISC BRAKE BUSHING DUST BOOT


    C108949
  1. Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.



21. REMOVE REAR DISC BRAKE CYLINDER MOUNTING


    C108950
  1. Remove the 2 bolts and rear disc brake cylinder mounting from the axle beam.



22. REMOVE REAR DISC


    C151123E03
  1. Remove the rear disc.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Place matchmarks on the disc and axle hub.