SLIDING ROOF HOUSING > REMOVAL |
| 1. REMOVE SLIDING ROOF SIDE GARNISH LH |
![]() |
Remove the sliding roof side garnish LH.
| 2. REMOVE SLIDING ROOF SIDE GARNISH RH |
| 3. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY |
![]() |
Using a T25 "TORX" driver, remove the 6 screws.
Remove the sliding roof glass sub-assembly.
| 4. REMOVE TILT ROOF GLASS SUB-ASSEMBLY |
![]() |
Using a T20 "TORX" driver, remove the 6 screws and tilt roof glass sub-assembly.
| 5. REMOVE ROOF HEADLINING ASSEMBLY |
| 6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock and disconnect the curtain shield airbag connector.
| *1 | Protective Tape |
Remove the 5 bolts.

Remove the 4 clips.

![]() |
Using a clip remover, remove the 4 pins.
| *1 | Pin |
| *2 | Clip |
| *3 | Airbag |
| *4 | Body |
![]() |
Using a screwdriver with the tip wrapped with protective tape, separate the 4 clips and curtain shield airbag assembly from the body as shown in the illustration.
| *1 | Clip |
| *2 | Airbag |
| *3 | Body |
| *4 | Spacer |
Disengage the 5 hooks to remove the curtain shield airbag assembly.

Remove the 4 clips and 4 spacers from the curtain shield airbag assembly.
| 7. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH |
| 8. REMOVE REAR SIDE RAIL SPACER LH |
![]() |
Disengage the 2 clamps and remove the rear side rail spacer LH.
| 9. REMOVE REAR SIDE RAIL SPACER RH |
| 10. REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 2 bolts and sliding roof drive gear sub-assembly.
| 11. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH |
![]() |
Remove the 2 bolts, 2 nuts and front sliding roof housing mounting bracket LH.
| 12. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH |
| 13. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH |
![]() |
Remove the 2 bolts, 2 nuts and center sliding roof housing mounting bracket LH.
| 14. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH |
| 15. REMOVE SLIDING ROOF RAIL SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Disengage the clamp.
Remove the 12 nuts and sliding roof rail sub-assembly.

| 16. REMOVE MOON ROOF GLASS ASSEMBLY |
![]() |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
| *1 | Protective Tape |
![]() |
Place matchmarks on the moon roof glass assembly and vehicle body on the locations indicated in the illustration.
| *1 | Matchmark |
![]() |
Pass a piano wire between the rear slide roof panel sub-assembly and moon roof glass assembly from the interior, as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the moon roof glass assembly.
![]() |
Using suction cups, disengage the 2 clips and remove the moon roof glass assembly.
| 17. CLEAN MOON ROOF GLASS ASSEMBLY |
![]() |
Clean the outer edge of the moon roof glass with a non-residue solvent.
| 18. CLEAN REAR SLIDE ROOF PANEL SUB-ASSEMBLY |
![]() |
Using a scraper, remove the moulding and adhesive from the moon roof glass.
| *1 | Adhesive |
| *2 | Rear Slide Roof Panel Sub-assembly |
Clean and shape the contact surfaces of the rear slide roof panel sub-assembly.
Using a knife, cut away excess adhesive on the contact surfaces of the rear slide roof panel sub-assembly, as shown in the illustration.
Clean the contact surfaces of the rear slide roof panel sub-assembly with a piece of cloth saturated with cleaner.
| 19. REMOVE REAR SLIDE ROOF PANEL SUB-ASSEMBLY |
Remove the 16 nuts and rear slide roof panel sub-assembly.
