CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (RHD Models) |
| Symptom | Trouble Area |
| No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3. |
|


| 1.CHECK FOR SHORT TO +B IN CAN BUS WIRE (CAN NO. 1 J/C) |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the CAN No. 1 junction connector.
| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *2 | to CAN No. 2 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L61-6 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L61-14 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *3 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR SHORT TO +B IN CAN BUS WIRE (CAN NO. 1 J/C) |

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| L94-1 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter |
| L94-12 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L94-2 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU |
| L94-13 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L94-4 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Yaw rate sensor |
| L94-15 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L94-5 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Center airbag sensor assembly |
| L94-16 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L94-6 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Power management ECU |
| L94-17 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L94-7 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Transmission Control ECU |
| L94-18 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) | *2 | DLC3 |
| *3 | to Combination Meter | *4 | to Main Body ECU |
| *5 | to Yaw Rate Sensor | *6 | to Center Airbag Sensor Assembly |
| *7 | to Power Management Control ECU | *8 | to Transmission Control ECU |
| Result | Proceed to |
| OK | A |
| NG (to ECU or sensor wire) | B |
|
| ||||
| A | ||
| ||
| 3.CHECK FOR SHORT TO +B IN CAN BUS WIRE (CAN NO. 2 J/C) |
Disconnect the CAN No. 2 junction connector.

| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) | *2 | DLC3 |
| *3 | to Steering Angle Sensor | *4 | to Power Steering ECU |
| *5 | to Skid Control ECU | *6 | to DLC3 |
| *7 | to Navigation ECU | *8 | to CAN No. 1 Junction Connector |
| *9 | to Certification ECU | *10 | to ECM |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| L95-1 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Steering angle sensor |
| L95-12 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-2 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Power steering ECU |
| L95-13 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-3 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Skid control ECU |
| L95-14 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-4 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | DLC3 |
| L95-15 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-5 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Navigation ECU |
| L95-16 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-6 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | CAN No. 1 junction connector |
| L95-17 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-7 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Certification ECU |
| L95-18 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| L95-9 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| L95-20 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (to DLC3 branch wire) | B |
| NG (to CAN No. 1 J/C main wire) | C |
| NG (to ECU or sensor wire) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 4.CHECK FOR SHORT TO +B IN CAN BUS WIRE (ECU, SENSOR) |
Reconnect the CAN No. 1 Junction connector and CAN No. 2 junction connector.
Disconnect the ECU or sensor connected to the CAN bus wire that is shorted to B+.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L61-6 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L61-14 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||