Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Air Conditioner / Data List.

  5. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Room temperature sensor /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual cabin temperature displayed
    -
    Ambient Temp Sensor
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    -
    Adjusted Ambient Temp
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    -
    -
    Evaporator Fin Thermistor
    Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature displayed
    -
    Evaporator Target Temp
    Evaporator target temperature /
    Min.: -327.68°C (-557.82°F)
    Max.: 327.67°C (621.81°F)
    Evaporator target temperature displayed
    -
    Solar Sensor (D side)
    Solar sensor /
    Min.: 0
    Max.: 255
    Solar sensor value increases as brightness increases
    -
    Engine Coolant Temp
    Engine coolant temperature sensor /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature displayed
    -
    Set Temperature (D side)
    Set temperature /
    Min.: 65°F (18°C)
    Max.: 85°F (32°C)
    Actual set temperature displayed
    -
    Blower Motor Speed Level
    Blower motor speed level /
    Min.: 0
    Max.: 31
    Displayed speed level increases in range between 0 and 31 as blower motor speed increases
    -
    Regulator Pressure Sensor
    Air conditioning pressure sensor /
    Min.: -0.45668 MPaG
    Max.: 3.29437 MPaG
    Actual regulator pressure displayed
    -
    Air Mix Servo Targ Pulse (D)
    Air mix servo motor target pulse /
    Min.: 0
    Max.: 255
    MAX. COLD: 6 (pulse)
    MAX. HOT: 93 (pulse)
    -
    Air Mix Servo Actual Pulse (D)
    Air mix servo motor actual pulse /
    Min.: 0
    Max.: 255
    MAX. COLD: 6 (pulse)
    MAX. HOT: 93 (pulse)
    -
    Air Outlet Servo Pulse (D)
    Air outlet servo motor target pulse /
    Min.: 0
    Max.: 255
    FACE: 47 (pulse)
    B/L: 37 (pulse)
    FOOT: 17 (pulse)
    FOOT/DEF: 9 (pulse)
    DEF: 5 (pulse)
    -
    Air Outlet Servo Actu Pulse (D)
    Air outlet servo motor actual pulse /
    Min.: 0
    Max.: 255
    FACE: 47 (pulse)
    B/L: 37 (pulse)
    FOOT: 17 (pulse)
    FOOT/DEF: 9 (pulse)
    DEF: 5 (pulse)
    -
    Air Inlet Damper Targ Pulse
    Air inlet servo motor target pulse /
    Min.: 0
    Max.: 255
    for LHD:
    1. RECIRCULATION: 19 (pulse)
    2. FRESH: 7 (pulse)
    for RHD:
    1. RECIRCULATION: 7 (pulse)
    2. FRESH: 25 (pulse)
    -
    Air Inlet Damper Actual Pulse
    Air inlet servo motor actual pulse /
    Min.: 0
    Max.: 255
    for LHD:
    1. RECIRCULATION: 19 (pulse)
    2. FRESH: 7 (pulse)
    for RHD:
    1. RECIRCULATION: 7 (pulse)
    2. FRESH: 25 (pulse)
    -
    Compressor Speed
    Compressor speed /
    Min.: 0 rpm
    Max.: 65535 rpm
    Displays actual rotation speed in the range between 0 rpm and 10000 rpm
    -
    Compressor Target Speed
    Compressor target speed /
    Min.: 0 rpm
    Max.: 65535 rpm
    Displays actual rotation speed in the range between 0 rpm and 10000 rpm
    -
    Electric Heater Active Level*1
    Heater active level /
    Min.: 0
    Max.: 3
    Actual electric heater active level displayed
    -
    ECO Switch
    ECO MODE switch /
    OFF or ON
    OFF: ECO MODE switch off
    ON: ECO MODE switch on
    -
    Solar Ventilation Switch*2
    Solar ventilation switch (Switch recognition value at A/C amplifier side) /
    OFF or ON
    OFF: solar ventilation switch off
    ON: solar ventilation switch on
    -
    Number of Trouble Codes
    Number of trouble codes /
    Min.: 0
    Max.: 255
    Number of DTCs displayed
    -

    1. *1: w/ PTC Heater Assembly
    2. *2: w/ Solar Ventilation System


ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Air Conditioner / Active Test.

  5. Check the operation by referring to the table below.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower motor
    Min.: 0, Max.: 31
    -
    Compressor Target Speed
    Compressor with motor assembly
    Min.: 0, Max.: 10000
    -
    Water Pump
    Engine water pump
    OFF or ON
    -
    Electrical Fan
    Electrical fan
    OFF or ON
    -
    Heater Active Level*1
    Heater active level
    Min.: 0, Max.: 3
    -
    Defogger Relay (Rear)
    Defogger relay (Rear)
    OFF or ON
    -
    Mirror Heater Relay (Front)
    Mirror heater relay (Front)
    OFF or ON
    -
    Air Mix Servo Targ Pulse (D)
    Air mix servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse (D)
    Air outlet servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 0, Max.: 255
    -

    1. *1: w/ PTC Heater Assembly