AIR CONDITIONING UNIT > INSTALLATION |
| 1. TEMPORARILY TIGHTEN AIR CONDITIONING UNIT ASSEMBLY |
![]() |
Temporarily tighten the air conditioning unit assembly with the bolt and the nut.
Engage the the cooler drain hose as shown in the illustration.
| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Install the instrument panel reinforcement assembly with the 6 bolts <A>.
Install the air conditioning unit assembly with the 3 bolts <B>

Engage each clamp.

| 3. INSTALL AIR CONDITIONING UNIT ASSEMBLY |
![]() |
Install the air conditioning unit with the nut assembly with the bolt and nut.
| 4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY |
![]() |
Install the No. 3 air duct sub-assembly with the 2 nuts.
| 5. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY |
![]() |
Engage the 6 claws and remove the lower defroster nozzle assembly.
Engage the clamp.
| 6. INSTALL DEFROSTER NOZZLE ASSEMBLY |
![]() |
Install the defroster nozzle assembly as shown in the illustration.
![]() |
Engage the 3 claws.
| 7. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the No. 2 instrument panel brace sub-assembly with the screw.
Install the bolt and nut.
Install the screw <B> and 2 nuts to the computer integration box RH.
Engage each clamp.
Connect each connector.
Install the 3 screws <A>.
Install the bolt and connect the earth wire.

| *1 | Screw <A> | *2 | Bolt |
| *3 | Earth wires | *4 | Screw <B> |
| *5 | Nut | *6 | Computer integration box RH |
| 8. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the No. 1 instrument panel brace sub-assembly with the screw.
Install the bolt and nut.
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Connect the center airbag sensor connectors to the center airbag sensor assembly as shown in the illustration.
Check that the waterproof sheet on the top of the center airbag sensor is not folded or deformed.
Check that there is no looseness in the installation parts of the center airbag sensor assembly.
Connect each connector.
Engage each clamp and claw.
Install the screw.
Install the 2 bolts and connect the 2 earth wires.

| *1 | Center airbag sensor connector | *2 | Screw |
| *3 | Bolt | *4 | Earth wires |
| *5 | Waterproof Sheet | - | - |
| 9. INSTALL NO. 3 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Install the No. 3 side defroster nozzle duct with the clip.
| 10. INSTALL REAR NO. 1 AIR DUCT |
![]() |
Engage the 4 claws to install the rear No. 1 air duct.
| 11. INSTALL REAR NO. 3 AIR DUCT |
![]() |
Engage the 2 claws to install the rear No. 3 air duct.
![]() |
Engage the 2 claws and install the clip.
Engage the fastener to install the floor carpet to the original position as shown in the illustration.
| *1 | Fastener |
![]() |
Engage each claw to close the door scuff plate clamps as shown in the illustration.
| 12. INSTALL REAR NO. 2 AIR DUCT |
![]() |
Engage the 2 claws to install the rear No. 2 air duct.
![]() |
Engage the 2 claws and install the clip.
Engage the fastener to install the floor carpet to the original position as shown in the illustration.
| *1 | Fastener |
![]() |
Engage each claw to close the door scuff plate clamps as shown in the illustration.
| 13. INSTALL STEERING POST ASSEMBLY |
![]() |
Install the steering post assembly with the bolt and 2 nuts.
Connect the connectors and engage the wire harness clamps to the steering post assembly.
![]() |
Connect the connector to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
Engage the 2 wire harness clamps.
| 14. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
| *1 | Matchmark |
Install the bolt.
| 15. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 16. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY |
![]() |
Engage the 2 claws to install the No. 2 air duct sub-assembly.
| 17. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY |
| 18. INSTALL PUSH ROD PIN |
| 19. INSTALL BRAKE PEDAL RETURN SPRING |
| 20. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER |
| 21. INSTALL STOP LIGHT SWITCH ASSEMBLY |
![]() |
Insert the stop light switch assembly until the rod hits the pedal.
![]() |
Make a quarter turn clockwise to install the stop light switch assembly.
Connect the connector.
Check the protrusion of the rod.
| 22. INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for LHD) |
![]() |
Engage the claw to install the connector as shown in the illustration.
![]() |
Engage the claw to lock the connector lock as shown in the illustration.
![]() |
Engage the claw to connect the connector as shown in the illustration.
![]() |
Engage the 2 clamps to connect the wire harness.
![]() |
Engage the 6 claws to install the junction block cover.
![]() |
Install the driver side junction block assembly with the bolt and nut.
![]() |
Engage the 2 claws to connect the 2 connectors (5) and (4) as shown in the illustration.
Connect the 3 connectors (3), (2) and (1) as shown in the illustration.
Engage the clamp to connect the wire harness.
| 23. INSTALL FRONT PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (for RHD) |
![]() |
Engage the claw to connect the connector as shown in the illustration.
![]() |
Engage the claw to lock the connector lock as shown in the illustration.
![]() |
Engage the claw to connect the connector as shown in the illustration.
Engage the clamp to connect the wire harness.
![]() |
Install the front passenger side junction block assembly with the bolt and nut.
Engage the 2 clamps to connect the wire harness.
![]() |
Engage the 2 claws to connect the 2 connectors (3) and (2) as shown in the illustration.
Connect the connector (1).
| 24. INSTALL ECU INTEGRATION BOX LH (for RHD) |
![]() |
Install the ECU integration box with the bolt and nut.
Engage the clamp to connect the wire harness.
| 25. INSTALL HEADUP DISPLAY |
![]() |
Install the headup display with the bolt and 2 nuts.
Connect the connector.
Engage the clamp.
| 26. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD) |
When using a new lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.

Install the lower instrument panel sub-assembly with the 4 bolts <B>, 11 bolts <C> and screw <D>.

| *1 | Bolt <B> | *2 | Bolt <C> |
| *3 | Screw <D> | - | - |
Engage each clamp.

| 27. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD) |
When using a new lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.

Install the lower instrument panel sub-assembly with the 4 bolts <B>, 11 bolts <C> and screw <D>.

| *1 | Bolt <B> | *2 | Bolt <C> |
| *3 | Screw <D> | - | - |
Engage each clamp.
Engage the 2 claws.

| 28. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD) |
for Connector Type Antenna Cord:
![]() |
Engage the 4 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the connector.
for Plug Type Antenna Cord:
![]() |
Engage the 5 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the 2 connectors.
| 29. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD) |
for Connector Type Antenna Cord:
![]() |
Engage the 5 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the connector.
for Plug Type Antenna Cord:
![]() |
Engage the 6 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the 2 connectors.
| 30. INSTALL INSTRUMENT PANEL SAFETY PAD PLATE SUB-ASSEMBLY (for LHD) |
![]() |
Install the instrument panel safety pad plate sub-assembly with the 2 bolts <B>.
| 31. INSTALL POWER STEERING ECU ASSEMBLY |
![]() |
Install the power steering ECU assembly with the bolt and 2 nuts.
![]() |
Connect the 3 connectors to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
| *1 | Lock Lever |
| *2 | Lock of the Lock Lever |
Engage the wire harness clamp to the power steering ECU assembly.
| 32. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Engage the clip.
Install the combination meter assembly with the 3 screws.
Engage the clamp.
Connect the 3 connectors.
| 33. INSTALL NO. 1 HEATER TO REGISTER DUCT |
![]() |
Install the No. 1 heater to register duct with the 3 clips.
| 34. INSTALL COWL SIDE TRIM BOARD RH |
| 35. INSTALL FRONT DOOR SCUFF PLATE RH |
| 36. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.
| *a | Opened Approximately 55° |
| *b | Closed |
![]() |
Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
| *1 | Glove Compartment Door Stopper Sub-assembly |
| *2 | Stopper |
Engage the claw and connect the glove compartment door stopper sub-assembly.
| 37. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Connect the connector.
![]() |
Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.
| 38. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the airbag connector and install the clamp to the driver side knee airbag assembly.
Push in the lock to install the airbag connector.
![]() |
Temporarily install the driver side knee airbag assembly with the 6 claws and 4 guides.
![]() |
Install the driver side knee airbag assembly with the 4 bolts.
| 39. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD) |
Connect each connector.
![]() |
Engage the guide and claw.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.
| 40. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD) |
Connect each connector.
![]() |
Engage the guide and 2 claws.
Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.
| 41. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 42. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Using pliers, expand the clamp.
| *1 | Clamp |
| *2 | Claw |
While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
Return the clamp to its original position.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 43. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Engage the 2 claws and 2 pins to install the upper steering column cover.
| 44. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Engage the 4 claws.
![]() |
Engage the 2 claws.
| 45. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
| *1 | Matchmark |
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 46. INSTALL STEERING PAD |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the airbag connector to the steering pad.
Push in the lock to install the airbag connector.
Connect the horn connector to the steering pad.
![]() |
Push the steering pad to engage the 2 pins.
| 47. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Engage the claw to install the lower No. 3 steering wheel cover.
| 48. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Engage the claw to install the lower No. 2 steering wheel cover.
| 49. INSTALL NO. 1 SWITCH HOLE BASE |
Connect the connector.
![]() |
Engage the 5 claws to install the No. 1 switch hole base.
| 50. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
![]() |
Temporarily install the console box assembly.
![]() |
Engage the 9 claws as shown in the illustration.
![]() |
Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.
Engage the clamp.
| 51. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY |
![]() |
Install the shift lock control unit assembly with the 3 nuts.
Connect the connector to the shift lock control unit assembly.
| 52. INSTALL AIR CONDITIONING CONTROL ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 claws to install the air conditioning control assembly.
| 53. INSTALL CONSOLE BOX ASSEMBLY |
Connect each connector.
![]() |
Engage the 4 guides and 2 claws as shown in the illustration.
![]() |
Install the console box assembly with the bolt <B> and 2 clips.
| 54. INSTALL BOX BOTTOM MAT |
![]() |
Engage the fastener to install the box bottom mat.
| 55. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.
| 56. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.
| 57. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET |
![]() |
Install the No. 2 console box mounting bracket with the 6 bolts <B>.
| 58. INSTALL ELECTRICAL KEY OSCILLATOR |
![]() |
Engage the clamp and install the electrical key oscillator.
Connect the connector.
| 59. INSTALL REAR CONSOLE BOX ASSEMBLY |
Connect the connector.
![]() |
Engage the 8 claws as shown in the illustration.
![]() |
Install the rear console box assembly with the 5 bolts.
| 60. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 61. INSTALL UPPER CONSOLE PANEL |
![]() |
Engage the 3 claws to install the upper console panel.
| 62. INSTALL REAR CONSOLE BOX POCKET |
![]() |
Install the rear console box pocket as shown in the illustration.
| 63. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY |
When using a new upper instrument panel sub-assembly:
Immediately before installing the upper instrument panel assembly, twist and cut off the portions shown in the illustration.

Engage the 5 claws as shown in the illustration.
Engage the 2 claws and 4 clips, and install the upper instrument panel assembly as shown in the illustration.

Install the 2 bolts <B>.
Install the 2 passenger airbag bolts <A>.

| *1 | Passenger Airbag Bolt <A> | *2 | Bolt <B> |
Engage the 2 clamps.
Connect each connector.

| 64. CONNECT NO. 3 INSTRUMENT PANEL WIRE |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the connector.
| 65. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Connect the connector.
Engage the 7 claws.
Install the center instrument cluster finish panel garnish with the 2 screws <C>.

| 66. INSTALL INSTRUMENT CLUSTER FINISH PANEL END |
![]() |
Engage the 2 guides and 5 claws to install the instrument cluster finish panel end as shown in the illustration.
| 67. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
| 68. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides and 6 claws to install the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.
| 69. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH |
![]() |
Engage the 3 claws to install the front pillar garnish corner piece RH.
| 70. INSTALL FRONT PILLAR GARNISH RH |
| 71. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Connect the connector.
Install the front No. 2 speaker assembly with the 2 bolts.
| 72. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides and 6 claws to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.
| 73. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH |
![]() |
Engage the 3 claws to install the front pillar garnish corner piece LH.
| 74. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the protective cover.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
![]() |
Make sure that the front pillar garnish clip is not damaged.
| *1 | Front Pillar Garnish Clip |
| *2 | Protective Tape |
Engage the claw to direction indicated by the arrow (1).
Engage the 3 guides to direction indicated by the arrow (2).
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.
![]() |
Engage 2 clips to install the front pillar garnish LH.
| 75. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
Engage the guide as shown in the illustration.
![]() |
Engage the guide as shown in the illustration.
![]() |
Engage the 4 claws to install the instrument panel finish panel end RH.
| 76. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 77. INSTALL GLOVE COMPARTMENT DOOR |
Open the glove compartment door assembly.
![]() |
Insert the glove compartment door as shown in the illustration.
Engage the 7 claws to install the glove compartment door.
| 78. INSTALL NO. 2 INSTRUMENT PANEL REGISTER |
![]() |
Engage the 3 claws and clip to install the No. 2 instrument panel register.
| 79. INSTALL NO. 1 SIDE DEFROSTER NOZZLE |
![]() |
Engage the 3 claws to install the No. 1 side defroster nozzle.
| 80. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
Engage the guide as shown in the illustration.
![]() |
Engage the guide as shown in the illustration.
![]() |
Engage the 4 claws to install the instrument panel finish panel end LH.
| 81. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 82. INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL |
![]() |
Engage the 4 claws to install the No. 1 center instrument cluster finish panel.
| 83. INSTALL NO. 1 INSTRUMENT PANEL REGISTER |
![]() |
Engage the 4 claws to install the No. 1 instrument panel register.
| 84. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
Connect each connector.
Engage the clamp.
![]() |
Engage the 2 guides and claw to connect the hood lock control cable.
![]() |
Engage the 6 claws and clip.
![]() |
Install the lower instrument panel finish panel assembly with the screw <C>.
| 85. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim board LH with the clip.
| 86. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 10 claws to install the front door scuff plate LH.
| 87. INSTALL NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System) |
![]() |
Engage the 4 claws to temporarily install the navigation receiver assembly with bracket as shown in the illustration.
![]() |
Install the navigation receiver assembly with bracket with the 4 bolts.
| 88. INSTALL RADIO RECEIVER WITH BRACKET (w/o Navigation System) |
Connect each connector.
![]() |
Engage the 4 claws as shown in the illustration.
![]() |
Install the radio receiver with bracket with the 4 bolts.
| 89. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver) |
![]() |
Install the radio tuner opening cover with bracket with the 4 bolts <B>.
| 90. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver) |
![]() |
Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.
| 91. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.
| 92. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Connect the connector.
Engage the 14 claws to install the instrument cluster finish panel garnish.

| 93. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.
| 94. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Connect each connector.
Engage the 6 claws to install the integration control and panel assembly.
| 95. CONNECT OUTLET HEATER WATER HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the outlet heater water hose.
| 96. CONNECT INLET HEATER WATER HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the inlet heater water hose.
| 97. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.
Install the O-ring on the air conditioning tube and accessory assembly.
Install the air conditioning tube and accessory assembly.
| 98. CONNECT SUCTION PIPE SUB-ASSEMBLY |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
Install the O-ring on the suction pipe sub-assembly.
Install the suction pipe sub-assembly.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 99. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp to install the wire harness.
| 100. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Install the outer cowl top panel with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp*2 of the wire harness.
Engage the clamp*1 and connect the connector (w/ Windshield Deicer).
![]() |
Engage the clamp of the wire harness.
| 101. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 102. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 103. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Engage the grommet as shown in the illustration.
| *1 | Grommet |
Install the windshield wiper motor and link assembly with the 2 bolts.
Connect the connector.
| 104. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
Engage the 8 guides <B>.

Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.
![]() |
Install the 2 clips.
| 105. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
Engage the 8 guides <B>.

Engage the 6 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.
![]() |
Install the 2 clips.
| 106. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Engage the guide <B> as shown in the illustration.
Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.
| 107. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 108. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
When reusing the front wiper arm and blade assembly RH:
Clean the wiper arm serrations.
| *1 | Wiper Arm Serration |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serration |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| *1 | Ceramic Dot |
| 109. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
When reusing the front wiper arm and blade assembly LH:
Clean the wiper arm serrations.
| *1 | Wiper Arm Serration |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serration |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| *1 | Ceramic Dot |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.
| 110. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the 3 claws to install the front wiper arm head cap.
| 111. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 112. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 113. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 114. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 115. ADD COOLANT (for Engine) |
Tighten the radiator drain cock plug.
Tighten the cylinder block drain cock plug.
Remove the reservoir tank cap.
Connect the hose to the air release valve.
Loosen the air release valve.
Add TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank filler opening until coolant overflows from the air release valve. Then tighten the air release valve.
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Disconnect the hose from the air release valve.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Put the engine in inspection mode (Click here).
Install the reservoir tank cap and air release valve, and warm up the engine sufficiently.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 116. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 117. WARM UP COMPRESSOR |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 118. INSPECT FOR REFRIGERANT LEAK |
After recharging with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the refrigerant lines.
| *1 | Inspect for Leak |
| *2 | Halogen Leak Detector |
![]() |
Bring the halogen leak detector close to the drain hose with the detector's power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 119. INSPECT FOR COOLANT LEAK (for Engine) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.
| 120. INSPECT SHIFT LEVER |
Turn the power switch on (READY).
Check that all available shift positions can be selected moving the shift lever.
| 121. INSPECT STEERING PAD |
Inspect the steering pad .
| 122. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).