Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. TEMPORARILY TIGHTEN AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
  1. Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
  2. When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



    E189221
  1. Temporarily tighten the air conditioning unit assembly with the bolt and the nut.

  1. Engage the the cooler drain hose as shown in the illustration.

    NOTICE:
    Connect the cooler drain hose firmly to prevent water leaks.



2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Install the instrument panel reinforcement assembly with the 6 bolts <A>.



  1. Install the air conditioning unit assembly with the 3 bolts <B>.

    Torque:
    Torque: <B>:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    HINT:
    Tighten the bolts in the order shown in the illustration.



    E189219E01



  1. Engage each clamp.


    E189218



3. INSTALL AIR CONDITIONING UNIT ASSEMBLY


    E190902
  1. Install the air conditioning unit with the nut assembly with the bolt and nut.

    Torque:
    Bolt:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
    Nut:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    E189217
  1. Install the No. 3 air duct sub-assembly with the 2 nuts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



5. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY


    E189216
  1. Engage the 6 claws and remove the lower defroster nozzle assembly.

  1. Engage the clamp.



6. INSTALL DEFROSTER NOZZLE ASSEMBLY


    E189215
  1. Install the defroster nozzle assembly as shown in the illustration.



    E189213
  1. Engage the 3 claws.



7. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E189212
  1. Install the No. 2 instrument panel brace sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the bolt and nut.

  1. Install the screw <B> and 2 nuts to the computer integration box RH.

  1. Engage each clamp.

  1. Connect each connector.

  1. Install the 3 screws <A>.



  1. Install the bolt and connect the earth wire.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    E189209E01


    Text in Illustration 
    *1
    Screw <A>
    *2
    Bolt
    *3
    Earth wires
    *4
    Screw <B>
    *5
    Nut
    *6
    Computer integration box RH



8. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E189207
  1. Install the No. 1 instrument panel brace sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the bolt and nut.

  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Connect the center airbag sensor connectors to the center airbag sensor assembly as shown in the illustration.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Check that the waterproof sheet on the top of the center airbag sensor is not folded or deformed.

  1. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  1. Connect each connector.

  1. Engage each clamp and claw.

  1. Install the screw.



  1. Install the 2 bolts and connect the 2 earth wires.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    E189206E01


    Text in Illustration 
    *1
    Center airbag sensor connector
    *2
    Screw
    *3
    Bolt
    *4
    Earth wires
    *5
    Waterproof Sheet
    -
    -



9. INSTALL NO. 3 SIDE DEFROSTER NOZZLE DUCT


    E189204
  1. Install the No. 3 side defroster nozzle duct with the clip.



10. INSTALL REAR NO. 1 AIR DUCT


    E189203
  1. Engage the 4 claws to install the rear No. 1 air duct.



11. INSTALL REAR NO. 3 AIR DUCT


    E189201
  1. Engage the 2 claws to install the rear No. 3 air duct.



    E189127E01
  1. Engage the 2 claws and install the clip.

  1. Engage the fastener to install the floor carpet to the original position as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



    E189123
  1. Engage each claw to close the door scuff plate clamps as shown in the illustration.



12. INSTALL REAR NO. 2 AIR DUCT


    E189202
  1. Engage the 2 claws to install the rear No. 2 air duct.



    E189119E01
  1. Engage the 2 claws and install the clip.

  1. Engage the fastener to install the floor carpet to the original position as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



    E189115
  1. Engage each claw to close the door scuff plate clamps as shown in the illustration.



13. INSTALL STEERING POST ASSEMBLY


    C206267
  1. Install the steering post assembly with the bolt and 2 nuts.

    Torque:
    Bolt:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.

  1. Connect the connectors and engage the wire harness clamps to the steering post assembly.



    C206266
  1. Connect the connector to the power steering ECU assembly.



    C206265
  1. Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.

  1. Engage the 2 wire harness clamps.



14. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C206262E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
    Text in Illustration 
    *1
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



15. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C206261
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



16. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


    C206263
  1. Engage the 2 claws to install the No. 2 air duct sub-assembly.



17. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
for LHD:
for RHD:


18. INSTALL PUSH ROD PIN
for LHD:
for RHD:


19. INSTALL BRAKE PEDAL RETURN SPRING
for LHD:
for RHD:


20. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER


21. INSTALL STOP LIGHT SWITCH ASSEMBLY


    E167768
  1. Insert the stop light switch assembly until the threaded sleeve hits the pedal.

    NOTICE:
    When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.



    E236346E01
  1. Make a quarter turn clockwise to install the stop light switch assembly.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    NOTICE:
    When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.

  1. Connect the connector.

  1. Check the protrusion of the plunger.
    Protrusion of Plunger 
    Area
    Measurement
    a
    0.5 to 2.6 mm (0.0197 to 0.102 in.)
    If the protrusion is not as specified, recheck switch installation and inspect brake pedal adjustment if necessary (Click here for LHD or Click here for RHD).

    NOTICE:
    Do not depress or support the brake pedal.



22. INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for LHD)


    E189807
  1. Engage the claw to install the connector as shown in the illustration.

    NOTICE:
    Be sure to engage each connector securely.



    E189453
  1. Engage the claw to lock the connector lock as shown in the illustration.



    E186347
  1. Engage the claw to connect the connector as shown in the illustration.

    NOTICE:
    Be sure to engage each connector securely.



    E189450
  1. Engage the 2 clamps to connect the wire harness.



    E189449
  1. Engage the 6 claws to install the junction block cover.



    E189448
  1. Install the driver side junction block assembly with the bolt and nut.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }



    E189447E01
  1. Engage the 2 claws to connect the 2 connectors (5) and (4) as shown in the illustration.

    NOTICE:
    Be sure to engage each connector securely.

  1. Connect the 3 connectors (3), (2) and (1) as shown in the illustration.

    NOTICE:
    Be sure to engage each connector securely.

  1. Engage the clamp to connect the wire harness.



23. INSTALL FRONT PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (for RHD)


    E189827
  1. Engage the claw to connect the connector as shown in the illustration.



    E189825
  1. Engage the claw to lock the connector lock as shown in the illustration.



    E189823
  1. Engage the claw to connect the connector as shown in the illustration.

  1. Engage the clamp to connect the wire harness.



    E189821
  1. Install the front passenger side junction block assembly with the bolt and nut.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }

  1. Engage the 2 clamps to connect the wire harness.



    E189820E01
  1. Engage the 2 claws to connect the 2 connectors (3) and (2) as shown in the illustration.

  1. Connect the connector (1).



24. INSTALL ECU INTEGRATION BOX LH (for RHD)


    E189818
  1. Install the ECU integration box with the bolt and nut.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }

  1. Engage the clamp to connect the wire harness.



25. INSTALL HEADUP DISPLAY


    E113762
  1. Install the headup display with the bolt and 2 nuts.

  1. Connect the connector.

  1. Engage the clamp.



26. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)


  1. When using a new lower instrument panel sub-assembly:



    1. Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.


      B233338



  1. Install the lower instrument panel sub-assembly with the 4 bolts <B>, 11 bolts <C> and screw <D>.


    B227299E01


    Text in Illustration 
    *1
    Bolt <B>
    *2
    Bolt <C>
    *3
    Screw <D>
    -
    -

  1. Engage each clamp.



27. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)


  1. When using a new lower instrument panel sub-assembly:



    1. Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.


      B234828



  1. Install the lower instrument panel sub-assembly with the 4 bolts <B>, 11 bolts <C> and screw <D>.


    B223640E01


    Text in Illustration 
    *1
    Bolt <B>
    *2
    Bolt <C>
    *3
    Screw <D>
    -
    -

  1. Engage each clamp.

  1. Engage the 2 claws.



28. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD)
  1. for Plug Type Antenna Cord:

    1. Engage the 4 clamps.

    2. Install the No. 2 antenna cord sub-assembly with the bolt.

    3. Connect the 2 connectors.

  1. for Connector Type Antenna Cord:

    1. Engage the 4 clamps.

    2. Install the No. 2 antenna cord sub-assembly with the bolt.

    3. Connect the connector.

  1. w/ Digital Audio Broadcasting Antenna:

    1. Engage the 5 clamps.

    2. Install the No. 2 antenna cord sub-assembly with the bolt.

    3. Connect the 2 connectors.



29. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD)
  1. Plug Type Antenna Cord:

    1. Engage the 5 clamps.

    2. Install the No. 2 antenna cord sub-assembly with the bolt.

    3. Connect the 2 connectors.

  1. for Connector Type Antenna Cord:

    1. Engage the 5 clamps.

    2. Install the No. 2 antenna cord sub-assembly with the bolt.

    3. Connect the connector.

  1. w/ Digital Audio Broadcasting Antenna:

    1. Engage the 6 clamps.

    2. Install the No. 2 antenna cord sub-assembly with the bolt.

    3. Connect the 2 connectors.



30. INSTALL POWER STEERING ECU ASSEMBLY


    C206237
  1. Install the power steering ECU assembly with the bolt and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    C206236
  1. Connect the 3 connectors to the power steering ECU assembly.



    C206235E01
  1. Connect the connector to the power steering ECU assembly.
    Text in Illustration 
    *1
    Lock Lever
    *2
    Lock of the Lock Lever

    HINT:
    As shown in the illustration, return the lock lever to its original position to connect the connector and securely push in the lock of the lock lever.

  1. Engage the wire harness clamp to the power steering ECU assembly.



31. INSTALL COMBINATION METER ASSEMBLY


    E113756
  1. Engage the clip.

  1. Install the combination meter assembly with the 3 screws.

  1. Engage the clamp.

  1. Connect the 3 connectors.



32. INSTALL NO. 1 HEATER TO REGISTER DUCT
  1. Install the No. 1 heater to register duct with the 3 clips.



33. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure for the RH side and LH side.



34. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side.



35. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B223650E01
  1. With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.
    Text in Illustration 
    *a
    Opened Approximately 55°
    *b
    Closed

    NOTICE:
    Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.



    B223648E01
  1. Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
    Text in Illustration 
    *1
    Glove Compartment Door Stopper Sub-assembly
    *2
    Stopper

  1. Engage the claw and connect the glove compartment door stopper sub-assembly.



36. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Connect the connector.

  1. Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.



37. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B226999
  1. Connect the airbag connector and install the clamp to the driver side knee airbag assembly.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the lock to install the airbag connector.



    B226997
  1. Temporarily install the driver side knee airbag assembly with the 6 claws and 4 guides.



    B226996
  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Confirm that the driver side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.



38. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
  1. Connect each connector.

  1. Engage the guide and claw.

  1. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.



39. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
  1. Connect each connector.

  1. Engage the guide and 2 claws.

  1. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.



40. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


41. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C206260E01
  1. Using pliers, expand the clamp.
    Text in Illustration 
    *1
    Clamp
    *2
    Claw

  1. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

  1. Return the clamp to its original position.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.



42. INSTALL UPPER STEERING COLUMN COVER


    C206259
  1. Engage the 2 claws and 2 pins to install the upper steering column cover.



43. INSTALL LOWER STEERING COLUMN COVER

NOTICE:
If the lower steering column cover is installed in the incorrect order, it will not be possible to assemble the lower steering column cover.



    C206256
  1. Engage the 2 claws to install the lower steering column cover.



    C206253
  1. Engage the 4 claws.



    C206257
  1. Engage the 2 claws.

    HINT:
    Press the area around the claws to engage them.



44. INSTALL STEERING WHEEL ASSEMBLY


    C248390E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.
    Text in Illustration 
    *1
    Matchmark

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



45. INSTALL STEERING PAD
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B232533
  1. Connect the airbag connector to the steering pad.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the lock to install the airbag connector.

  1. Connect the horn connector to the steering pad.



    B226981
  1. Push the steering pad to engage the 2 pins.

    NOTICE:
    Make sure that the pins are securely inserted into the steering holes.



46. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B226977
  1. Engage the claw to install the lower No. 3 steering wheel cover.



47. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B226979
  1. Engage the claw to install the lower No. 2 steering wheel cover.



48. INSTALL NO. 1 SWITCH HOLE BASE
  1. Connect the connector.

  1. Engage the 5 claws to install the No. 1 switch hole base.



49. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
  1. Temporarily install the console box assembly.



    B279576
  1. Engage the 9 claws as shown in the illustration.



    B223654
  1. Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.

  1. Engage the clamp.



50. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    C209262
  1. Install the shift lock control unit assembly with the 3 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the connector to the shift lock control unit assembly.



51. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
  1. Connect the connector.

    NOTICE:
    Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, take care to connect each connector to the correct component.



    E189054
  1. Engage the 4 claws to install the air conditioning control assembly.



52. INSTALL CONSOLE BOX ASSEMBLY
  1. Connect each connector.



    B279577
  1. Engage the 4 guides and 2 claws as shown in the illustration.

  1. Install the console box assembly with the bolt <B> and 2 clips.



53. INSTALL BOX BOTTOM MAT
  1. Engage the fastener to install the box bottom mat.



54. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B223646E01
  1. Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.



55. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B223644E01
  1. Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.



56. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET
  1. Install the No. 2 console box mounting bracket with the 6 bolts <B>.



57. INSTALL ELECTRICAL KEY OSCILLATOR


    B229283
  1. Engage the clamp and install the electrical key oscillator.

    NOTICE:
    Be careful when installing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

  1. Connect the connector.



58. INSTALL REAR CONSOLE BOX ASSEMBLY
  1. Connect each connector.



    B279596
  1. Engage the 8 claws as shown in the illustration.

  1. Install the rear console box assembly with the 5 bolts.



59. INSTALL CONSOLE BOX CARPET
  1. Install the console box carpet.



60. INSTALL REAR CONSOLE BOX CUP HOLDER


    B294664
  1. Engage the 4 claws to install the rear console box cup holder as shown in the illustration.



61. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY


  1. When using a new upper instrument panel sub-assembly:



    1. Immediately before installing the upper instrument panel assembly, twist and cut off the portions shown in the illustration.


      B233340



  1. Engage the 5 claws as shown in the illustration.


    B223501E01

  1. Engage the 2 claws and 4 clips, and install the upper instrument panel assembly as shown in the illustration.

  1. Install the 2 bolts <B>.

  1. Install the 2 passenger airbag bolts <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Engage the 2 clamps.

  1. Connect each connector.



62. CONNECT NO. 3 INSTRUMENT PANEL WIRE
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B228000
  1. Connect the connector.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.



63. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Connect the connector.

  1. Engage the 7 claws.

  1. Install the center instrument cluster finish panel garnish with the 2 screws <C>.



64. INSTALL INSTRUMENT CLUSTER FINISH PANEL END


    B223496E01
  1. Engage the 2 guides and 5 claws to install the instrument cluster finish panel end as shown in the illustration.



65. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

HINT:
Use the same procedure for the RH side and LH side.



66. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B223479E01
  1. Engage the 2 guides and 6 claws to install the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.



67. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH


    B223494
  1. Engage the 3 claws to install the front pillar garnish corner piece RH.



68. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.



69. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY


    E188475
  1. Connect the connector.

  1. Install the front No. 2 speaker assembly with the 2 bolts.



70. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B223477E01
  1. Engage the 2 guides and 6 claws to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.



71. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH


    B223475
  1. Engage the 3 claws to install the front pillar garnish corner piece LH.



72. INSTALL FRONT PILLAR GARNISH LH


    B227780E01
  1. Remove the protective cover.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly



    B257020E01
  1. Make sure that the front pillar garnish clip is not damaged.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip
    *2
    Protective Tape

    NOTICE:
    1. If there is any damage, replace the garnish clip with a new one.
    2. When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

  1. Engage the claw to direction indicated by the arrow (1).

  1. Engage the 3 guides to direction indicated by the arrow (2).

  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

    HINT:
    Tape the needle-nosed pliers tip before use.



    B257025
  1. Engage 2 clips to install the front pillar garnish LH.



73. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


    B223491
  1. Engage the guide as shown in the illustration.



    B223489
  1. Engage the guide as shown in the illustration.



    B223488
  1. Engage the 4 claws to install the instrument panel finish panel end RH.



74. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B227773E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (White)

    NOTICE:
    After installation, check that the corners fit correctly.



75. INSTALL GLOVE COMPARTMENT DOOR
  1. Open the glove compartment door assembly.



    B223486
  1. Insert the glove compartment door as shown in the illustration.

  1. Engage the 7 claws to install the glove compartment door.



76. INSTALL NO. 2 INSTRUMENT PANEL REGISTER


    B223484
  1. Engage the 3 claws and clip to install the No. 2 instrument panel register.



77. INSTALL NO. 1 SIDE DEFROSTER NOZZLE


    B223481
  1. Engage the 3 claws to install the No. 1 side defroster nozzle.



78. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    B223472
  1. Engage the guide as shown in the illustration.



    B223470
  1. Engage the guide as shown in the illustration.



    B223469
  1. Engage the 4 claws to install the instrument panel finish panel end LH.



79. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B227774E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



80. INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL
  1. Engage the 4 claws to install the No. 1 center instrument cluster finish panel.



81. INSTALL NO. 1 INSTRUMENT PANEL REGISTER


    B223466
  1. Engage the 4 claws to install the No. 1 instrument panel register.



82. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
  1. Connect each connector.

  1. Engage the clamp.

  1. Engage the 2 guides and claw to connect the hood lock control cable.



    B298864
  1. Engage the 6 claws and clip.

  1. Install the lower instrument panel finish panel assembly with the screw <C>.



83. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B227764
  1. Engage the 2 clips.

  1. Install the cowl side trim board LH with the clip.



84. INSTALL FRONT DOOR SCUFF PLATE LH


    B227761
  1. Engage the 10 claws to install the front door scuff plate LH.



85. INSTALL NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    E188508
  1. Engage the 4 claws and temporarily install the navigation receiver with bracket as shown in the illustration.

  1. Install the navigation receiver with bracket with the 4 bolts.



86. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
  1. Connect each connector.

  1. Engage the 4 claws.

  1. Install the radio and display receiver assembly with bracket with the 4 bolts.



87. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    B223593
  1. Install the radio tuner opening cover with bracket with the 4 bolts <B>.



88. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    B227341
  1. Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.



89. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Connect the connector.

  1. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.



90. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Connect the connector.

  1. Engage the 14 claws to install the instrument cluster finish panel garnish.



91. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223456
  1. Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.



92. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223453
  1. Connect each connector.

  1. Engage the 6 claws to install the integration control and panel assembly.



93. CONNECT OUTLET HEATER WATER HOSE


    E189103
  1. Using pliers, grip the claws of the clip and slide the clip to connect the outlet heater water hose.



94. CONNECT INLET HEATER WATER HOSE


    E189102
  1. Using pliers, grip the claws of the clip and slide the clip to connect the inlet heater water hose.



95. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring on the air conditioning tube and accessory assembly.

    NOTICE:
    1. Keep the O-ring and O-ring fitting surfaces clean from dirt or any foreign objects.
    2. Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.

  1. Install the air conditioning tube and accessory assembly.



96. CONNECT SUCTION PIPE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring on the suction pipe sub-assembly.

    NOTICE:
    1. Keep the O-ring and O-ring fitting surfaces clean from dirt or any foreign objects.
    2. Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.

  1. Install the suction pipe sub-assembly.



    E189107
  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



97. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C209144
  1. Install the outer cowl top panel sub-assembly with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C209145
  1. Bend the water guard plate RH and engage the claw.



    C209147
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205696
  1. Engage the clamp to install the wire harness.



98. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C205557
  1. Install the outer cowl top panel with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C205561
  1. Bend the water guard plate RH and engage the claw.



    C205559
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205555E01
  1. Engage the clamp*2 of the wire harness.

  1. Engage the clamp*1 and connect the connector (w/ Windshield Deicer).



    C205556
  1. Engage the clamp of the wire harness.



99. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)


    C209143
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



100. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD)


    C205554
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



101. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


  1. Connect the connector.


    E222808E01


    Text in Illustration 
    *A
    for LHD:
    *B
    for RHD:
    *1
    Grommet
    -
    -

  1. Engage the grommet as shown in the illustration.

  1. Install the windshield wiper motor and link assembly with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.

    NOTICE:
    Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



102. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


  1. Engage the 8 guides <B>.


    E190042E01

  1. Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.



    E190113
  1. Install the 2 clips.



103. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


  1. Engage the 8 guides <B>.


    E187005E01

  1. Engage the 6 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.



    E187016
  1. Install the 2 clips.



104. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E193125E01
  1. Engage the guide <B> as shown in the illustration.

  1. Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.



105. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



106. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



    E112237E06
  1. When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wire Brush
      *3
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



    E189301E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.



107. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E112237E05
  1. When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wire Brush
      *3
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



    E189303E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



108. INSTALL FRONT WIPER ARM HEAD CAP


    E190044
  1. Engage the 3 claws to install the front wiper arm head cap.

    HINT:
    Use the same procedure for the RH side and LH side.



109. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



110. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



111. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



112. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



113. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Remove the reservoir tank cap.



    A213418E01
  1. Add coolant to B line of the reservoir tank.
    Text in Illustration 
    *1
    B Line

    Standard Capacity:
    Item
    Capacity
    Engine coolant
    w/ Exhaust Heat Recirculation System:
    7.2 liters (7.6 US qts, 6.3 lmp. qts)
    w/o Exhaust Heat Recirculation System:
    6.5 liters (6.8 US qts, 5.7 lmp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the reservoir tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

      HINT:
      The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    2. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.



    A213418E02
  1. After the engine has cooled down, check that the coolant level is between full and low.
    Text in Illustration 
    *1
    Full Line
    *2
    Low Line
    If the coolant level is low, add coolant to the full line on the reservoir tank.



114. CHARGE WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.



  1. Charge with refrigerant HFC-134a (R134a).


    E143108E05

    Standard:
    470 g (16.6 oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C on before charging with refrigerant. Doing so will cause the compressor to work without refrigerant, resulting in overheating of the cooler compressor.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, not with the sight glass.
    3. Avoid using the gauge manifold set that had been used for vehicles with conventional compressor oil (ND-OIL 8 or equivalent) as much as possible. This will cause compressor oil remaining in the manifold to enter the vehicle, resulting in insulation performance deterioration. A gauge manifold set that had been used 3 times or less can be reused if an appropriate one is not available.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an A/C system.



115. WARM UP COMPRESSOR
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.



116. INSPECT FOR REFRIGERANT LEAK
  1. After recharging with refrigerant, inspect for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Turn the power switch off.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)



    I042222E31
  1. Using a halogen leak detector, inspect for refrigerant leaks from the refrigerant lines.
    Text in Illustration 
    *1
    Inspect for Leak
    *2
    Halogen Leak Detector



    N014519E08
  1. Bring the halogen leak detector close to the drain hose with the detector's power off, and then turn the detector on.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *2
    Drain Hose

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.

  1. If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



117. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the reservoir tank cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. Remove the reservoir tank cap.



    A213419
  1. Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  1. Remove the radiator cap tester.

  1. Install the reservoir tank cap.



118. INSPECT SHIFT LEVER
  1. Turn the power switch on (READY).

  1. Check that all available shift positions can be selected moving the shift lever.

    HINT:
    After the shift lever is replaced with a new one, perform the above operation. If this operation is not performed, moving the shift lever may not initially select shift positions.



119. INSPECT STEERING PAD
  1. Inspect the steering pad .



120. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).