AIR CONDITIONING UNIT > INSTALLATION |
| 1. TEMPORARILY TIGHTEN AIR CONDITIONING UNIT ASSEMBLY |
![]() |
Temporarily tighten the air conditioning unit assembly with the bolt and the nut.
Connect the drain cooler hose.
| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Install the instrument panel reinforcement assembly with the 6 bolts <A>.
Install the air conditioning unit assembly with the 3 bolts <B>.

Engage each clamp.

| 3. INSTALL AIR CONDITIONING UNIT ASSEMBLY |
![]() |
Install the air conditioning unit with the nut assembly with the bolt and nut.
| 4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY |
![]() |
Install the No. 3 air duct sub-assembly with the 2 nuts.
| 5. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY |
![]() |
Engage the 6 claws and remove the lower defroster nozzle assembly.
Engage the clamp.
| 6. INSTALL DEFROSTER NOZZLE ASSEMBLY |
![]() |
Install the defroster nozzle assembly as shown in the illustration.
![]() |
Engage the 3 claws.
| 7. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the No. 2 instrument panel brace sub-assembly with the screw.
Install the bolt and nut.
Install the screw <B> and 2 nuts to the computer integration box RH.
Engage each clamp.
Connect each connector.
Install the 3 screws <A>.
Install the bolt and connect the earth wire.

| *1 | Screw <A> | *2 | Bolt |
| *3 | Earth wires | *4 | Screw <B> |
| *5 | Nut | *6 | Computer integration box RH |
| 8. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the No. 1 instrument panel brace sub-assembly with the screw.
Install the bolt and nut.
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Connect the center airbag sensor connectors to the center airbag sensor assembly as shown in the illustration.
Check that the waterproof sheet on the top of the center airbag sensor is not folded or deformed.
Check that there is no looseness in the installation parts of the center airbag sensor assembly.
Connect each connector.
Engage each clamp and claw.
Install the screw.
Install the 2 bolts and connect the 2 earth wires.

| *1 | Center airbag sensor connector | *2 | Screw |
| *3 | Bolt | *4 | Earth wires |
| *5 | Waterproof Sheet | - | - |
| 9. INSTALL NO. 3 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Install the No. 3 side defroster nozzle duct with the clip.
| 10. INSTALL REAR NO. 1 AIR DUCT |
![]() |
Engage the 4 claws to install the rear No. 1 air duct.
| 11. INSTALL REAR NO. 3 AIR DUCT |
![]() |
Engage the 2 claws to install the rear No. 3 air duct.
![]() |
Engage the 2 claws and install the clip.
Engage the fastener to install the floor carpet to the original position as shown in the illustration.
| *1 | Fastener |
![]() |
Engage each claw to close the door scuff plate clamps as shown in the illustration.
| 12. INSTALL REAR NO. 2 AIR DUCT |
![]() |
Engage the 2 claws to install the rear No. 2 air duct.
![]() |
Engage the 2 claws and install the clip.
Engage the fastener to install the floor carpet to the original position as shown in the illustration.
| *1 | Fastener |
![]() |
Engage each claw to close the door scuff plate clamps as shown in the illustration.
| 13. INSTALL STEERING POST ASSEMBLY |
| 14. INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for LHD) |
![]() |
Engage the claw to install the connector as shown in the illustration.
![]() |
Engage the claw to lock the connector lock as shown in the illustration.
![]() |
Engage the claw to connect the connector as shown in the illustration.
![]() |
Engage the 2 clamps to connect the wire harness.
![]() |
Engage the 6 claws to install the junction block cover.
![]() |
Install the driver side junction block assembly with the bolt and nut.
![]() |
Engage the 2 claws to connect the 2 connectors (5) and (4) as shown in the illustration.
Connect the 3 connectors (3), (2) and (1) as shown in the illustration.
Engage the clamp to connect the wire harness.
| 15. INSTALL FRONT PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (for RHD) |
![]() |
Engage the claw to connect the connector as shown in the illustration.
![]() |
Engage the claw to lock the connector lock as shown in the illustration.
![]() |
Engage the claw to connect the connector as shown in the illustration.
Engage the clamp to connect the wire harness.
![]() |
Install the front passenger side junction block assembly with the bolt and nut.
Engage the 2 clamps to connect the wire harness.
![]() |
Engage the 2 claws to connect the 2 connectors (3) and (2) as shown in the illustration.
Connect the connector (1).
| 16. INSTALL ECU INTEGRATION BOX LH (for RHD) |
![]() |
Install the ECU integration box with the bolt and nut.
Engage the clamp to connect the wire harness.
| 17. INSTALL HEADUP DISPLAY |
![]() |
Install the headup display with the bolt and 2 nuts.
Connect the connector.
Engage the clamp.
| 18. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
| 19. CONNECT OUTLET HEATER WATER HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the outlet heater water hose.
| 20. CONNECT INLET HEATER WATER HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the inlet heater water hose.
| 21. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.
Install the O-ring on the air conditioning tube and accessory assembly.
Install the air conditioning tube and accessory assembly.
| 22. CONNECT SUCTION PIPE SUB-ASSEMBLY |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
Install the O-ring on the suction pipe sub-assembly.
Install the suction pipe sub-assembly.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 23. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp to install the wire harness.
| 24. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Install the outer cowl top panel with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp*2 of the wire harness.
Engage the clamp*1 and connect the connector (w/ Windshield Deicer).
![]() |
Engage the clamp of the wire harness.
| 25. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 26. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 27. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 28. ADD COOLANT (for Engine) |
Tighten the radiator drain cock plug.
Remove the reservoir tank cap.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the reservoir tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 29. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 30. WARM UP COMPRESSOR |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 31. INSPECT FOR REFRIGERANT LEAK |
After recharging with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the refrigerant lines.
| *1 | Inspect for Leak |
| *2 | Halogen Leak Detector |
![]() |
Bring the halogen leak detector close to the drain hose with the detector's power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 32. INSPECT FOR COOLANT LEAK (for Engine) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.