FRONT WIPER MOTOR > INSTALLATION |
| 1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY |
![]() |
Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.
| 2. INSTALL FRONT WIPER CRANK SUB-ASSEMBLY |
When replacing the windshield wiper motor assembly and front wiper crank sub-assembly with a new one:
![]() |
Temporarily install a front wiper crank sub-assembly on the new windshield wiper motor assembly with the nut.
![]() |
Temporarily install the windshield wiper motor and link on the crank arm pivot of the front wiper crank sub-assembly.
Align the front wiper crank sub-assembly with the windshield wiper motor and link as shown in the illustration.

| *1 | Front Wiper Crank Sub-assembly |
Tighten install the front wiper crank sub-assembly with the nut.
When reusing the windshield wiper motor assembly and front wiper crank sub-assembly:
![]() |
Align the matchmarks to install the front wiper crank sub-assembly with the nut.
| *1 | Matchmark |
![]() |
Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.
| *1 | Crank Arm Pivot |
![]() |
Connect the rod of the windshield wiper link assembly to the crank arm pivot of the front wiper crank sub-assembly.
| 3. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Engage the grommet as shown in the illustration.
| *1 | Grommet |
Install the windshield wiper motor and link assembly with the 2 bolts.
Connect the connector.
| 4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
Engage the 8 guides <B>.

Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.
![]() |
Install the 2 clips.
| 5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
Engage the 8 guides <B>.

Engage the 6 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.
![]() |
Install the 2 clips.
| 6. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Engage the guide <B> as shown in the illustration.
Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.
| 7. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
When reusing the front wiper arm and blade assembly RH:
Clean the wiper arm serrations.
| *1 | Wiper Arm Serration |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serration |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| *1 | Ceramic Dot |
| 9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
When reusing the front wiper arm and blade assembly LH:
Clean the wiper arm serrations.
| *1 | Wiper Arm Serration |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serration |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| *1 | Ceramic Dot |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.
| 10. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the 3 claws to install the front wiper arm head cap.