Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR

FRONT WIPER MOTOR > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER ARM HEAD CAP


    E190045E01
  1. Using a screwdriver, disengage the 3 claws to remove the front wiper arm head cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the RH side and LH side.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E190049
  1. Remove the nut and the front wiper arm and blade assembly LH.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E190048
  1. Remove the nut and the front wiper arm and blade assembly RH.



4. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E193124E01
  1. Using a screwdriver, disengage the claw and guide <A> as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the guide <B> and remove the cowl side ventilator sub-assembly LH as shown in the illustration.



5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E190113
  1. Remove the 2 clips.



  1. Disengage the 5 claws and 3 guides <A>.


    E190043E02

  1. Disengage the 8 guides <B> and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.



7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E187016
  1. Remove the 2 clips.



  1. Disengage the 6 claws and 3 guides <A>.


    E187004E01

  1. Disengage the 8 guides <B> and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.



8. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


  1. Disengage the 2 clamps.


    E222807E01


    Text in Illustration 
    *A
    for LHD:
    *B
    for RHD:
    *1
    Grommet
    -
    -

  1. Remove the 2 bolts.

  1. Disengage the grommet as shown in the illustration.

  1. Disconnect the connector.

  1. Remove the windshield wiper motor and link assembly.

    NOTICE:
    Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.



9. REMOVE FRONT WIPER CRANK SUB-ASSEMBLY


    E214674E01
  1. Using a screwdriver, separate the windshield wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



  1. When reusing the windshield wiper motor assembly and front wiper crank sub-assembly:



      E190053E01
    1. Place matchmarks on the windshield wiper link assembly and front wiper crank sub-assembly.
      Text in Illustration 
      *1
      Matchmark



    E190959
  1. Remove the nut and the front wiper crank sub-assembly.



10. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY


    E214675
  1. Using a T30 "TORX" socket wrench, remove the 2 bolts and the windshield wiper motor assembly from the windshield wiper link assembly.