FRONT DOOR LOCK > INSTALLATION |
| 1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System) |
![]() |
Install the front door inside locking cable assembly as shown in the illustration.
| 2. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System) |
![]() |
Install the front door inside locking cable assembly as shown in the illustration.
| 3. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System) |
![]() |
Install the front door lock remote control cable assembly as shown in the illustration.
![]() |
Engage the 7 claws as shown in the illustration.
| 4. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System) |
![]() |
Install the front door lock remote control cable assembly as shown in the illustration.
![]() |
Engage the 7 claws as shown in the illustration.
| 5. INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Double Locking System) |
Apply MP grease to the sliding parts of the front door lock assembly.
![]() |
Install a new door lock wiring harness seal to the front door lock assembly.
![]() |
Insert the front door lock open rod to the front door lock assembly.
Make sure that the front door lock open rod is securely connected to the front door lock assembly.
Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.
| 6. INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Double Locking System) |
Apply MP grease to the sliding parts of the front door lock assembly.
![]() |
Install a new door lock wiring harness seal to the front door lock assembly.
![]() |
Insert the front door lock open rod to the front door lock assembly.
Make sure that the front door lock open rod is securely connected to the front door lock assembly.
Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.
| 7. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Install the front door outside handle cover with lock cylinder assembly.
![]() |
Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.
![]() |
Install the hole plug.
| 8. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Install the front door rear lower frame sub-assembly with the bolt as shown in the illustration.
| 9. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 10. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
w/ Navigation System for HDD:
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the grommet.
Connect the cable to the negative (-) battery terminal.
| 11. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply butyl tape to the front door panel.
![]() |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
Attach the front door service hole cover according to the reference points on the front door panel.
| *1 | Reference Point |
| 12. INSTALL FRONT DOOR TRIM BRACKET |
![]() |
Install the front door trim bracket with the 2 screws.
| 13. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
![]() |
Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.
| 14. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Engage the 9 clips and install the front door trim board sub-assembly.
Install the 2 screws.
Remove the 2 pieces of protective tape.
| 15. INSTALL COURTESY LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw to install the courtesy light assembly.
| 16. INSTALL DOOR ARMREST COVER |
![]() |
Install the door armrest cover.
| 17. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Connect the connector.
Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.
| 18. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect the connector.
![]() |
Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.
| 19. INSTALL ASSIST GRIP COVER |
![]() |
Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.
| 20. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws and install the front door inside handle bezel plug.
| 21. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 22. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 23. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 24. INITIALIZE POWER WINDOW CONTROL SYSTEM |
| 25. CHECK POWER WINDOW CONTROL SYSTEM |