Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B228655
  1. Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.



5. REMOVE ASSIST GRIP COVER


    B228659
  1. Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the assist grip cover.



6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B228663
  1. Disengage the 7 claws and 3 guides.

  1. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.



7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B232008
  1. Disengage the 7 claws and 3 guides.

  1. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.



8. REMOVE DOOR ARMREST COVER


    B228665
  1. Remove the door armrest cover.



9. REMOVE COURTESY LIGHT ASSEMBLY


    E189695E01
  1. Using a moulding remover, disengage the claw.

  1. Disconnect the connector and remove the courtesy light assembly.



10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B228667E01
  1. Put protective tape around the front door panel.
    Text in Illustration 
    *1
    Protective Tape



    B228669
  1. Remove the 2 screws.

  1. Using a clip remover, disengage the 9 clips.

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.



    B228673
  1. Disengage the 2 claws and disconnect the front door inside handle sub-assembly.



11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B228675
  1. Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.



12. REMOVE FRONT DOOR TRIM BRACKET


    B228685
  1. Remove the 2 screws and front door trim bracket.



13. REMOVE FRONT DOOR SERVICE HOLE COVER


    B228687
  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B228691
  1. Remove the grommet.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    1. w/ Navigation System for HDD:

      NOTICE:
      After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    B228693
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B228697E01
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.



15. REMOVE FRONT DOOR GLASS RUN


    B228703
  1. Remove the front door glass run.



16. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B228710
  1. Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.



17. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B228714
  1. Remove the hole plug.



    B228716
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



18. REMOVE FRONT DOOR LOCK ASSEMBLY (w/o Double Locking System)


    B228738
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.



    B228744
  1. Remove the door lock wiring harness seal from the front door lock assembly.



19. REMOVE FRONT DOOR LOCK ASSEMBLY (w/ Double Locking System)


    B228742
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.



    B228746
  1. Remove the door lock wiring harness seal from the front door lock assembly.



20. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)


    B228747
  1. Using a screwdriver, disengage the 7 claws as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.



    B228754
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



21. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)


    B228751
  1. Using a screwdriver, disengage the 7 claws as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.



    B228758
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



22. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)


    B228760
  1. Remove the front door inside locking cable assembly as shown in the illustration.



23. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)


    B228764
  1. Remove the front door inside locking cable assembly as shown in the illustration.