REAR DOOR LOCK > INSTALLATION |
| 1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System) |
![]() |
Install the rear door inside locking cable assembly as shown in the illustration.
![]() |
Engage the 4 claws as shown in the illustration.
| 2. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System) |
![]() |
Install the rear door inside locking cable assembly as shown in the illustration.
![]() |
Engage the 4 claws as shown in the illustration.
| 3. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System) |
![]() |
Install the rear door lock remote control cable assembly as shown in the illustration.
![]() |
Engage the 2 claws as shown in the illustration.
| 4. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System) |
![]() |
Install the rear door lock remote control cable assembly as shown in the illustration.
![]() |
Engage the 2 claws as shown in the illustration.
| 5. INSTALL REAR DOOR LOCK ASSEMBLY (w/o Double Locking System) |
Apply MP grease to the sliding parts of the rear door lock assembly.
![]() |
Install a new door lock wiring harness seal to the rear door lock assembly.
![]() |
Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.
Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.
| 6. INSTALL REAR DOOR LOCK ASSEMBLY (w/ Double Locking System) |
Apply MP grease to the sliding parts of the rear door lock assembly.
![]() |
Install a new door lock wiring harness seal to the rear door lock assembly.
![]() |
Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.
Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.
| 7. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.
Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly and rear power window regulator motor connector.
w/ Navigation System for HDD:
Disconnect the cable from the negative (-) battery terminal.
![]() |
Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.
Install the rear door glass sub-assembly with the 2 bolts.
Connect the cable to the negative (-) battery terminal.
| 8. INSTALL REAR DOOR REAR GUIDE SEAL |
Install the temporary screw to the rear door rear guide seal.
![]() |
Temporarily install the rear door rear guide seal.
| *1 | Temporary Screw |
Install the 2 screws.
Tighten the temporary screw to install the rear door rear guide seal.
| 9. INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY |
![]() |
Install the screw.
Install the rear door window guide sub-assembly with the bolt.
| 10. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 11. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *1 | Reference Point |
Connect the 2 connectors.
Engage the clamp.
| 12. INSTALL REAR DOOR TRIM BRACKET |
![]() |
Install the rear door trim bracket with the 2 screws.
| 13. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
![]() |
Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
| 14. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
for 8 Speakers:
Connect the connector.
![]() |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 2 screws.
Remove the protective tape.
| 15. INSTALL REAR DOOR ARMREST COVER |
![]() |
Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.
| 16. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
Connect the connector.
![]() |
Engage the 7 claws and 2 guides, and install the rear power window regulator switch assembly with rear door armrest base panel.
| 17. INSTALL DOOR ASSIST GRIP COVER |
![]() |
Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.
| 18. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws and install the rear door inside handle bezel plug.
| 19. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 20. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 21. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 22. INITIALIZE POWER WINDOW CONTROL SYSTEM |
| 23. CHECK POWER WINDOW CONTROL SYSTEM |