Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > INSPECTION

for Preparation Click here



1. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)


    B228541E01
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → Terminal 4 (L)
      Battery negative (-) → Terminal 1 (UL)
      Locks
      Battery positive (+) → Terminal 1 (UL)
      Battery negative (-) → Terminal 4 (L)
      Unlocks

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly LH)
      *2
      Lock
      *3
      Unlock
      If the result is not as specified, replace the rear door lock assembly LH.



    B228541E02
  1. Check the operation of the unlock detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Locked
      10 kΩ or higher
      6 (LSSR) - 9 (E)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly LH)
      *2
      Lock
      *3
      Unlock
      If the result is not as specified, replace the rear door lock assembly LH.



2. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)


    B228543E01
  1. Check the operation of the door lock motor and double lock motor.

    1. Apply battery voltage and check the operation of the door lock motor and double lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Locks
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unlocks
      Battery positive (+) → 4 (DL)
      Battery negative (-) → 3 (UNDL)
      Sets
      Battery positive (+) → 3 (UNDL)
      Battery negative (-) → 4 (DL)
      Unsets

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly LH)
      *2
      Lock
      *3
      Unlock

      HINT:
      1. Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.
      2. Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

      If the result is not as specified, replace the rear door lock assembly LH.



    B228543E02
  1. Check the operation of the unlock detection switch and double lock position switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      5 (LSSR) - 6 (E)
      Locked
      10 kΩ or higher
      5 (LSSR) - 6 (E)
      Unlocked
      Below 1 Ω
      9 (DLSR) - 10 (E)
      Unset
      10 kΩ or higher
      9 (DLSR) - 10 (E)
      Set
      Below 1 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly LH)
      *2
      Lock
      *3
      Unlock
      If the result is not as specified, replace the rear door lock assembly LH.



3. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)


    B228542E01
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → Terminal 4 (L)
      Battery negative (-) → Terminal 1 (UL)
      Locks
      Battery positive (+) → Terminal 1 (UL)
      Battery negative (-) → Terminal 4 (L)
      Unlocks

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly RH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the rear door lock assembly RH.



    B228542E02
  1. Check the operation of the unlock detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Locked
      10 kΩ or higher
      6 (LSSR) - 9 (E)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly RH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the rear door lock assembly RH.



4. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)


    B228544E01
  1. Check the operation of the door lock motor and double lock motor.

    1. Apply battery voltage and check the operation of the door lock motor and double lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Locks
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unlocks
      Battery positive (+) → 2 (DL)
      Battery negative (-) → 1 (UNDL)
      Sets
      Battery positive (+) → 1 (UNDL)
      Battery negative (-) → 2 (DL)
      Unsets

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly RH)
      *2
      Unlock
      *3
      Lock

      HINT:
      1. Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.
      2. Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

      If the result is not as specified, replace the rear door lock assembly RH.



  1. Check the operation of the unlock detection switch and double lock position switch.



      B228544E02
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      9 (LSSR) - 10 (E)
      Locked
      10 kΩ or higher
      9 (LSSR) - 10 (E)
      Unlocked
      Below 1 Ω
      5 (DLSR) - 6 (E)
      Unset
      10 kΩ or higher
      5 (DLSR) - 6 (E)
      Set
      Below 1 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Door Lock Assembly RH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the rear door lock assembly RH.