Home › Drivetrain › P410 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM

ELECTRONIC SHIFT LEVER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
  1. Some Data List values may vary significantly if there are slight differences in the environment in which the vehicle is operating when measurements are obtained. Variations may also occur due to aging of the vehicle. Due to these considerations, it is not always possible to provide definite values to be used for judgment of malfunctions. It is possible that a malfunction may be present even if measured values are within the reference range.
  2. In the event of a problem with intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the Data List.

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values. when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the power switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the power switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Chassis / Transmission Control / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    HINT:
    When reading the Data List information, first determine which items need to be monitored before proceeding. Attempting to view all of the data may result in a delayed, inaccurate inspection.


    Transmission Control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift Pos Display (P)
    Shift position display (P) /
    ON or OFF
    ON: Park (P) selected
    OFF: A shift state other than park (P) selected
    (When normal)
    (May go off during malfunction)
    -
    Shift Pos Display (Not P)
    Shift position display (not P) /
    ON or OFF
    ON: A shift state other than park (P) selected
    (When normal)
    (May go off during malfunction)
    OFF: Park (P) selected
    -
    Master Caution Display
    Master caution display /
    Disp or Nondisp
    Disp: Malfunction occurs in this system
    Nondisp: Malfunction does not occur in this system
    Transmission control ECU assembly
    PSW Indicator Mode
    PSW indicator mode /
    ON or OFF
    ON: Park (P) selected
    OFF: A shift state other than park (P) selected
    (When normal)
    (May go off under malfunction)
    -
    U Phase Voltage Value
    U phase voltage value /
    Min: 0 V, Max: 39 V
    9 to 14 V: On (IG)
    (If voltage is applied to the shift control actuator assembly: 0 V)
    Shift control actuator assembly [parking lock motor (MUA)] signal circuit
    V Phase Voltage Value
    V phase voltage value /
    Min: 0 V, Max: 39 V
    9 to 14 V: On (IG)
    (If voltage is applied to the shift control actuator assembly: 0 V)
    Shift control actuator assembly [parking lock motor(MVA)] signal circuit
    W Phase Voltage Value
    W phase voltage value /
    Min: 0 V, Max: 39 V
    9 to 14 V: On (IG)
    (If voltage is applied to the shift control actuator assembly: 0 V)
    Shift control actuator assembly [parking lock motor(MWA)] signal circuit
    Battery Voltage Value
    BATT voltage value /
    Min: 0 V, Max: 19 V
    8 to 16 V: On (IG)
    BATT signal circuit
    IG (+B) Voltage Value
    IG (+B) voltage value /
    Min: 0 V, Max: 19 V
    8 to 16 V: On (IG)
    +B signal circuit
    Cmplte of Learn Lck Pos
    Completion of learning lock position /
    OK or NG
    OK: On (IG)
    -
    Cmplte of Learn Unlck Pos
    Completion of learning unlock position /
    OK or NG
    OK: Power switch on (IG), Park (P) selected → Neutral (N) selected and number of trips after learning is less than 3 or power switch on (IG) and number of trips after learning is 3 or more
    NG: Power switch on (IG), a shift state other than Park (P) has not been selected and number of trips after learning is less than 3
    1. Learning: Power switch on (IG), Park (P) selected → Neutral (N) selected
    2. Learning will not complete if Neutral (N) has not been selected even if number of trips is 3 or more
    # of Trip Cuntr after Learn
    Number of trips after learning /
    Min: 0, Max: 65535
    Actual number of trips
    (Power switch on (IG))
    -
    Main Relay for Motor Drive
    P CON MTR relay (transaxle parking lock control relay) for motor drive /
    ON or OFF
    OK: On (IG)
    -
    U Phase Crnt-Carry Status
    U phase current-carrying status /
    ON or OFF
    ON: U phase current flows
    OFF: U phase current does not flow
    Shift control actuator assembly [parking lock motor (MUA)] signal circuit
    V Phase Crnt-Carry Status
    V phase current-carrying status /
    ON or OFF
    ON: V phase current flows
    OFF: V phase current does not flow
    Shift control actuator assembly [parking lock motor (MVA)] signal circuit
    W Phase Crnt-Carry Status
    W phase current-carrying status /
    ON or OFF
    ON: W phase current flows
    OFF: W phase current does not flow
    Shift control actuator assembly [parking lock motor (MWA)] signal circuit
    U Phase Voltage Status
    U phase voltage status /
    ON or OFF
    ON: 9 to 14 V
    OFF: 0 V
    Shift control actuator assembly [parking lock motor (MUA)] signal circuit
    V Phase Voltage Status
    V phase voltage status /
    ON or OFF
    ON: 9 to 14 V
    OFF: 0 V
    Shift control actuator assembly [parking lock motor (MVA)] signal circuit
    W Phase Voltage Status
    W phase voltage status /
    ON or OFF
    ON: 9 to 14 V
    OFF: 0 V
    Shift control actuator assembly [parking lock motor (MWA)] signal circuit
    Battery Voltage Status
    BATT voltage status /
    ON or OFF
    ON: 8 to 16 V
    OFF: Below 8 V
    BATT signal circuit
    IG (+B) Phase Vol Status
    IG (+B) phase voltage status /
    ON or OFF
    ON: 10 to 16 V
    OFF: Below 10 V
    +B signal circuit
    ACC Condition Signal
    ACC condition signal /
    ON or OFF
    ON: 5 V or higher
    OFF: Below 5 V
    Judged according to the ACC signal via CAN communication line
    Init Drv Cntrl Completed
    Initial drive control completed /
    OK or NG
    OK: On (IG)
    -
    Cmplte of Detct Lck Pos
    Completion of detecting lock position /
    OK or NG
    OK: On (IG)
    -
    Cmplte of Detct Unlck Pos
    Completion of detecting unlock position /
    OK or NG
    OK: Power switch on (IG), Park (P) selected → Neutral (N) selected and number of trips after learning is less than 3
    NG: Power switch on (IG) and number of trips after learning is 3 or more
    NG is displayed when P/Not P Move Shft Range is Set and number of trips is 3 or more
    P/Not P Move Shft Range
    P/Not P movable shift range /
    Set or Unset
    Set: Power switch on (IG), Park (P) selected → Neutral (N) selected and number of trips after learning is less than 3 or power switch on (IG) and number of trips after learning is 3 or more
    Unset: Power switch on (IG), a shift state other than Park (P) has not been selected and number of trips after learning is less than 3
    -
    Main Relay
    P CON MTR relay (transaxle parking lock control relay) /
    Normal or Abnoml
    Normal: On (IG)
    -
    Current flag record
    Current flag record
    ON or OFF
    ON: Current flag record stored
    OFF: Current flag record not stored
    -
    Number of Trip after Low Voltage Actuator Abnormal
    Number of trips after shift control actuator assembly malfunction due to decrease in auxiliary battery voltage occurred /
    Min: 0, Max: 31
    -
    Only for vehicles produced September 2013 or later
    Low Voltage Actuator Abnormal History
    History of shift control actuator assembly malfunctions due to decrease in auxiliary battery voltage /
    ON or OFF
    -
    Only for vehicles produced September 2013 or later
    Number of Diagnosis Code
    Number of diagnosis codes /
    Min: 0, Max: 255
    Actual number of DTCs
    -