Home › Drivetrain › P410 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM

DTC    C2304    Open or Short Circuit in U Phase

DTC    C2305    Open or Short Circuit in V Phase

DTC    C2306    Open or Short Circuit in W Phase

for Preparation Click here


DESCRIPTION

The shift control actuator consists of the parking lock motor and the rotation angle sensor. The transmission control ECU receives a P position switch signal from the power management control ECU (HV CPU) and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. The transmission control ECU outputs these DTCs when it detects a malfunction in the parking lock motor system.

DTC No.
DTC Detection Condition
Trouble Area
C2304
With the power switch on (IG) (battery voltage is 8 V or more), voltage of transmission control ECU terminal MUA is 6 V or less for 1 second or more.
  1. Auxiliary battery
  2. Transmission control ECU assembly
  3. Shift control actuator assembly
  4. P CON MTR relay (Transaxle parking lock control relay)
  5. Wire harness or connector
C2305
With the power switch on (IG) (battery voltage is 8 V or more), voltage of transmission control ECU terminal MVA is 6 V or less for 1 second or more.
C2306
With the power switch on (IG) (battery voltage is 8 V or more), voltage of transmission control ECU terminal MWA is 6 V or less for 1 second or more.

WIRING DIAGRAM

Refer to the wiring diagram for DTC C2301 .

INSPECTION PROCEDURE

NOTICE:
  1. Do not remove/install the auxiliary battery or disconnect the cable from the battery terminal before instructed.
  2. Do not disconnect the connectors before instructed.
  3. It is not possible to clear the following DTCs using the intelligent tester: DTCs C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). After the repair, it is necessary to disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs.

1.CHECK DTC OUTPUT (TRANSMISSION CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    C2304, C2305 and C2306 are detected simultaneously
    A
    One of C2304, C2305 and C2306 is detected
    B

    HINT:
    1. If DTCs C2304, 2305 and 2306 are stored at the same time, there may be a malfunction in the parking lock motor (BMA signal) power source circuit.
    2. If DTC C2304, 2305 or 2306 is stored individually, there may be a malfunction in the parking lock motor (MUA, MVA or MWA signal) circuits.

  1. Turn the power switch off.



B
Go to step 6
A


2.CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Read the freeze frame data of C2304, 2305 and 2306.

    Result:
    Result
    Proceed to
    IG (+B) voltage is 9 V or more
    A
    IG (+B) voltage is less than 9 V
    B

  1. Turn the power switch off.



B
Go to step 7
A


3.CLEAR DTC
  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Turn the power switch off.

  1. Disconnect the P CON MAIN fuse and wait for at least 60 seconds.

  1. Check for DTCs again to see if the DTCs are cleared.


NEXT


4.CHARGE AUXILIARY BATTERY
  1. Charge the auxiliary battery.


NEXT


5.CHECK DTC OUTPUT (SIMULATION TEST)
  1. Connect the intelligent tester to the DLC3.

  1. Release the brake pedal and turn the power switch on (IG).

    HINT:
    Do not turn the power switch on (READY).

  1. Depress the brake pedal and move the selector lever to N.

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    C2304, 2305 or 2306 is output
    A
    DTC is not output.
    B

  1. Turn the power switch off.



B
END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)
A


6.READ VALUE USING INTELLIGENT TESTER (U, V, W VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Data List / U Phase Voltage Value, V Phase Voltage Value, W Phase Voltage Value.

  1. Read the Data List displayed on the intelligent tester.

    Result:
    Tester Display
    Switch Condition
    Specified Condition
    U Phase Voltage Value
    Power switch on (IG)
    9 to 14 V
    V Phase Voltage Value
    Power switch on (IG)
    9 to 14 V
    W Phase Voltage Value
    Power switch on (IG)
    9 to 14 V

  1. Turn the power switch off.



NG
Go to step 10
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)  

7.CLEAR DTC
  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Turn the power switch off.

  1. Disconnect the P CON MAIN fuse and wait for at least 60 seconds.

  1. Check for DTCs again to see if the DTCs are cleared.


NEXT


8.INSPECT AUXILIARY BATTERY
  1. Inspect the auxiliary battery (Click here).

    Result:
    Result
    Proceed to
    Charge or replace the auxiliary battery.
    A
    The auxiliary battery voltage is normal.
    B



B
Go to step 4
A


9.CHARGE OR REPLACE AUXILIARY BATTERY
  1. Charge or replace the auxiliary battery (Click here).



NEXT
Go to step 5

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR)
  1. Disconnect the A23 transmission control ECU assembly connector.

  1. Disconnect the D2 shift control actuator assembly connector.



    C210299E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-5 (MUA) - D2-1 (MUA)
    Power switch off
    Below 1 Ω
    A23-2 (MVA) - D2-6 (MVA)
    Power switch off
    Below 1 Ω
    A23-1 (MWA) - D2-7 (MWA)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-5 (MUA) or D2-1 (MUA) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A23-2 (MVA) or D2-6 (MVA) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A23-1 (MWA) or D2-7 (MWA) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)
    *2
    Front view of wire harness connector
    (to Shift Control Actuator Assembly)

  1. Connect the shift control actuator assembly connector.

  1. Connect the transmission control ECU assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P CON MTR RELAY)
  1. Disconnect the D2 shift control actuator assembly connector.

  1. Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room junction block assembly.



    C226007E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    D2-2 (BMA) - 5 (P CON MTR relay)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    D2-2 (BMA) or 5 (P CON MTR relay) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Junction Block Assembly
    *a
    Front view of wire harness connector
    (to Shift Control Actuator Assembly)

  1. Reinstall the P CON MTR relay (transaxle parking lock control relay).

  1. Connect the shift control actuator assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY
  1. Disconnect the A23 transmission control ECU assembly connector.

  1. Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room junction block assembly.



    C226008E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-5 (MUA) - 5 (P CON MTR relay)
    Power switch off
    Below 50 Ω
    A23-2 (MVA) - 5 (P CON MTR relay)
    Power switch off
    Below 50 Ω
    A23-1 (MWA) - 5 (P CON MTR relay)
    Power switch off
    Below 50 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-5 (MUA) - Body ground
    Power switch off
    10 kΩ or higher
    A23-2 (MVA) - Body ground
    Power switch off
    10 kΩ or higher
    A23-1 (MWA) - Body ground
    Power switch off
    10 kΩ or higher
    5 (P CON MTR relay) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Junction Block Assembly
    *a
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)

  1. Reinstall the P CON MTR relay (transaxle parking lock control relay).

  1. Connect the transmission control ECU assembly connector.



NG
REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY (Click here)
OK


13.INSPECT P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)


    C225994E01
  1. Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the P CON MTR relay (transaxle parking lock control relay).



NG
REPLACE P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)
OK


14.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MTR RELAY)
  1. Disconnect the A23 transmission control ECU assembly connector.

  1. Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room junction block assembly.



    C226008E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-23 (BMA) - 2 (P CON MTR relay)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-23 (BMA) or 2 (P CON MTR relay) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Junction Block Assembly
    *a
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)

  1. Reinstall the P CON MTR relay (transaxle parking lock control relay).

  1. Connect the transmission control ECU assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (P CON MTR RELAY - BODY GROUND)
  1. Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room junction block assembly.



    C226006E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    1 (P CON MTR relay) - Body ground
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Junction Block Assembly

  1. Reinstall the P CON MTR relay (transaxle parking lock control relay).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK HARNESS AND CONNECTOR (P CON MTR RELAY POWER SOURCE CIRCUIT)
  1. Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room junction block assembly.



    C226006E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (P CON MTR relay) - Body ground
    Always
    9 to 14 V

    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Junction Block Assembly

  1. Reinstall the P CON MTR relay (transaxle parking lock control relay).



NG
CHECK AND REPAIR POWER SOURCE CIRCUIT
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)