Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK WINDSHIELD WIPER RELAY ASSEMBLY

E125552E10

  1. Disconnect the L114 windshield wiper relay assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L114-4 (W) - Body ground
    B - Body ground
    Front washer switch circuit
    Front washer switch on
    Below 1 Ω
    Front washer switch off
    10 kΩ or higher
    L114-6 (VR2) - L114-7 (VR1)
    W - G
    Adjusting volume circuit
    Windshield wiper switch adjusting ring changed from (+) side to (-) side
    0 to 2.7 kΩ
    L114-8 (SIG) - Body ground
    BE - Body ground
    Power source circuit
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    L114-12 (IG) - Body ground
    B - Body ground
    Power source circuit
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    L114-23 (WIG) - Body ground
    B - Body ground
    Power source circuit
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    L114-26 (E) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L114 windshield wiper relay assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L114-1 (+2S) - Body ground
    R - Body ground
    Front wiper low speed signal circuit
    Power switch on (IG), front wiper switch in low position
    11 to 14 V
    Power switch on (IG), front wiper switch not in low position
    Below 1 V
    L114-2 (+1) - Body ground
    R - Body ground
    Front wiper motor low speed signal circuit
    Front wiper motor in low operation
    11 to 14 V
    Front wiper motor off
    Below 1 V
    L114-3 (+2) - Body ground
    W - Body ground
    Front wiper motor high speed signal circuit
    Front wiper motor in high operation
    11 to 14 V
    Front wiper motor off
    Below 1 V
    L114-4 (W) - Body ground
    B - Body ground
    Front washer motor circuit
    Front washer switch on
    Below 1 V
    Front washer switch off
    11 to 14 V
    L114-10 (+SM) - Body ground
    G - Body ground
    Front wiper motor operation signal
    Front wiper motor is in low or high operation
    11 to 14 V
    Front wiper motor off
    Below 1 V
    L114-11 (+SSW) - Body ground
    G - Body ground
    Front wiper motor operation signal
    Power switch on (IG), front wiper switch off or in AUTO, front wiper motor operates
    11 to 14 V
    Front wiper motor off
    Below 1 V
    L114-14 (PA1) - Body ground
    Y - Body ground
    Rain sensor signal
    Power switch on (IG)
    Pulse generation
    L114-17 (C1) - L114-16 (CO)
    V - Y
    IG signal circuit
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    L114-19 (SPD) - Body ground
    W - Body ground
    Speed signal
    Driving at approx. 20 km/h (12 mph)
    Pulse generation
    If the result is not as specified, the windshield wiper relay assembly may have a malfunction.


CHECK HEADLIGHT CLEANER CONTROL RELAY
  1. Disconnect the A44 headlight cleaner control relay connector.



  2. Measure the voltage and resistance according to the value(s) in the table below.


    E119074E05


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A44-2 (H) - A44-4 (E)
    LG - W-B
    Headlight cleaner switch operation signal
    Headlight cleaner switch off
    11 to 14 V
    Headlight cleaner switch on
    Below 1 V
    A44-3 (IG) - A44-4 (E)
    B - W-B
    Power switch on (IG) signal (Power source circuit)
    Power switch off
    Below 1 V
    Power switch on (IG)
    11 to 14 V
    A44-4 (E) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    A44-5 (FRWA) - A44-4 (E)
    R - W-B
    Front washer switch signal
    Front washer switch off
    11 to 14 V
    Front washer switch on
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B231709E01

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2C-35 - Body ground
    L - Body ground
    Low beam headlight signal
    Power switch on (IG), light control switch in head position
    Below 1 V
    Power switch on (IG), light control switch off
    4.2 V or higher