Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Wiper and Washer Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit detects the state of the windshield wiper switch assembly (front wiper switch and front washer switch) and sends it to the windshield wiper relay assembly.

WIRING DIAGRAM


E168181E05


INSPECTION PROCEDURE

1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY


    E171721E07
  1. for Light Control Switch LH Side Type:

    1. Remove the windshield wiper switch assembly (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      L48-3 (+1) - L48-1 (+S)
      OFF
      Below 1 Ω
      L48-3 (+1) - L48-2 (+B)
      MIST
      LO
      L48-2 (+B) - L48-4 (+2)
      HI
      L48-9 (AUTO) - L48-10 (E)
      AUTO
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-2 (EW) - L49-3 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Adjusting Ring*1:
      Tester Connection
      Condition
      Specified Condition
      L48-7 (VR1) - L48-8 (VR2)
      Adjusting ring changed from (+) side to (-) side
      0 to 2.7 kΩ

      Text in Illustration 
      *1
      Component without harness connected
      (to Windshield Wiper Switch Assembly)



    E169424E08
  1. for Light Control Switch RH Side Type:

    1. Remove the windshield wiper switch assembly (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      L48-2 (+1) - L48-4 (+S)
      OFF
      Below 1 Ω
      L48-2 (+1) - L48-3 (+B)
      MIST
      LO
      L48-3 (+B) - L48-1 (+2)
      HI
      L48-6 (AUTO) - L48-5 (E)
      AUTO
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-2 (EW) - L49-1 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Adjusting Ring*1:
      Tester Connection
      Condition
      Specified Condition
      L48-8 (VR1) - L48-7 (VR2)
      Adjusting ring changed from (+) side to (-) side
      0 to 2.7 kΩ

      Text in Illustration 
      *1
      Component without harness connected
      (to Windshield Wiper Switch Assembly)

      HINT:
      *1: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (WIPER SWITCH - WIPER RELAY AND BODY GROUND)
  1. for Light Control Switch LH Side Type:

    1. Disconnect the L49 and L48 windshield wiper switch assembly connectors.

    2. Disconnect the L114 windshield wiper relay assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L48-2 (+B) - L114-12 (IG)
      Always
      Below 1 Ω
      L48-2 (+B) - Body ground
      Always
      10 kΩ or higher
      L48-3 (+1) - L114-1 (+2S)
      Always
      Below 1 Ω
      L48-3 (+1) - Body ground
      Always
      10 kΩ or higher
      L48-4 (+2) - L114-3 (+2)
      Always
      Below 1 Ω
      L48-4 (+2) - Body ground
      Always
      10 kΩ or higher
      L48-1 (+S) - L114-11 (+SSW)
      Always
      Below 1 Ω
      L48-1 (+S) - Body ground
      Always
      10 kΩ or higher
      L48-9 (AUTO) - L114-17 (C1)
      Always
      Below 1 Ω
      L48-9 (AUTO) - Body ground
      Always
      10 kΩ or higher
      L48-10 (E) - L114-16 (CO)
      Always
      Below 1 Ω
      L48-10 (E) - Body ground
      Always
      10 kΩ or higher
      L48-7 (VR1) - L114-7 (VR1)
      Always
      Below 1 Ω
      L48-7 (VR1) - Body ground
      Always
      10 kΩ or higher
      L48-8 (VR2) - L114-6 (VR2)
      Always
      Below 1 Ω
      L48-8 (VR2) - Body ground
      Always
      10 kΩ or higher
      L49-3 (WF) - L114-4 (W)
      Always
      Below 1 Ω
      L49-3 (WF) - Body ground
      Always
      10 kΩ or higher
      L49-2 (EW) - Body ground
      Always
      Below 1 Ω

  1. for Light Control Switch RH Side Type:

    1. Disconnect the L49 and L48 windshield wiper switch assembly connectors.

    2. Disconnect the L114 windshield wiper relay assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L48-3 (+B) - L114-12 (IG)
      Always
      Below 1 Ω
      L48-3 (+B) - Body ground
      Always
      10 kΩ or higher
      L48-2 (+1) - L114-1 (+2S)
      Always
      Below 1 Ω
      L48-2 (+1) - Body ground
      Always
      10 kΩ or higher
      L48-1 (+2) - L114-3 (+2)
      Always
      Below 1 Ω
      L48-1 (+2) - Body ground
      Always
      10 kΩ or higher
      L48-4 (+S) - L114-11 (+SSW)
      Always
      Below 1 Ω
      L48-4 (+S) - Body ground
      Always
      10 kΩ or higher
      L48-6 (AUTO) - L114-17 (C1)
      Always
      Below 1 Ω
      L48-6 (AUTO) - Body ground
      Always
      10 kΩ or higher
      L48-5 (E) - L114-16 (CO)
      Always
      Below 1 Ω
      L48-5 (E) - Body ground
      Always
      10 kΩ or higher
      L48-8 (VR1) - L114-7 (VR1)
      Always
      Below 1 Ω
      L48-8 (VR1) - Body ground
      Always
      10 kΩ or higher
      L48-7 (VR2) - L114-6 (VR2)
      Always
      Below 1 Ω
      L48-7 (VR2) - Body ground
      Always
      10 kΩ or higher
      L49-1 (WF) - L114-4 (W)
      Always
      Below 1 Ω
      L49-1 (WF) - Body ground
      Always
      10 kΩ or higher
      L49-2 (EW) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)