WIPER AND WASHER SYSTEM > Front Wiper Motor Circuit |

| 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY |
for LHD:
Remove the windshield wiper motor assembly (Click here).
![]() |
Check low speed operation.
Connect a battery positive (+) lead to terminal 1 (+1) and a negative (-) lead to terminal 5 (E), and check that the motor operates at low speed.
Check high speed operation.
Connect a battery positive (+) lead to terminal 4 (+2) and a negative (-) lead to terminal 5 (E), and check that the motor operates at high speed.
| *1 | Component without harness connected (Windshield Wiper Motor Assembly) |
for RHD:
Remove the windshield wiper motor assembly (Click here).
![]() |
Check low speed operation.
Connect a battery positive (+) lead to terminal 5 (+1) and a negative (-) lead to terminal 4 (E), and check that the motor operates at low speed.
Check high speed operation.
Connect a battery positive (+) lead to terminal 3 (+2) and a negative (-) lead to terminal 4 (E), and check that the motor operates at high speed.
| *1 | Component without harness connected (Windshield Wiper Motor Assembly) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BATTERY AND BODY GROUND) |
for LHD:
![]() |
Disconnect the A35 windshield wiper motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-2 (B) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-5 (E) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Windshield Wiper Motor Assembly) |
for RHD:
![]() |
Disconnect the A35 windshield wiper motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-2 (B) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-4 (E) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Windshield Wiper Motor Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR - WINDSHIELD WIPER RELAY) |
for LHD:
Disconnect the L114 windshield wiper relay assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-1 (+1) - L114-2 (+1) | Always | Below 1 Ω |
| A35-1 (+1) - Body ground | Always | 10 kΩ or higher |
| A35-4 (+2) - L114-3 (+2) | Always | Below 1 Ω |
| A35-4 (+2) - Body ground | Always | 10 kΩ or higher |
| A35-3 (+S) - L114-10 (+SM) | Always | Below 1 Ω |
| A35-3 (+S) - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the L114 windshield wiper relay assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-5 (+1) - L114-2 (+1) | Always | Below 1 Ω |
| A35-5 (+1) - Body ground | Always | 10 kΩ or higher |
| A35-3 (+2) - L114-3 (+2) | Always | Below 1 Ω |
| A35-3 (+2) - Body ground | Always | 10 kΩ or higher |
| A35-1 (+S) - L114-10 (+SM) | Always | Below 1 Ω |
| A35-1 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||