Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > Image from Camera for Rear View Monitor is Abnormal

for Preparation Click here


DESCRIPTION

  1. The video signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM


E226207E10


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the L148 connector from the radio and display receiver assembly.

  1. Disconnect the V6 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L148-7 (CA+) - V6-4 (CB+)
    Always
    Below 1 Ω
    L148-8 (V+) - V6-2 (CV+)
    Always
    Below 1 Ω
    L148-15 (CGND) - V6-3 (CGND)
    Always
    Below 1 Ω
    L148-16 (V-) - V6-1 (CV-)
    Always
    Below 1 Ω
    L148-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    L148-8 (V+) - Body ground
    Always
    10 kΩ or higher
    L148-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    L148-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E216447E16
  1. Reconnect the L148 connector to the radio and display receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L148-15 (CGND) - Body ground
    Always
    Below 1 Ω
    L148-16 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L148-7 (CA+) - L148-15 (CGND)
    Power switch on (READY)
    Reverse (R) selected
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
  1. Reconnect the V6 connector to the rear television camera assembly.



    E224383E13
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

    OK:
    Waveform is similar to that shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    L148-8 (V+) - L146-7 (GND1)
    Tool Setting
    200 mV/DIV., 50 μs/DIV.
    Condition
    Power switch on (READY), reverse (R) selected

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)
    *b
    Waveform 1 (camera lens not covered, displaying an image)
    *c
    Waveform 2 (camera lens covered, blacking out the screen)
    *d
    Synchronization Signal
    *e
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)