Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL (for LHD)

PARKING BRAKE PEDAL (for LHD) > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    C206648
  1. Install the parking brake control pedal assembly with the bolt and 2 nuts.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }



    C206647
  1. Connect the parking brake switch connector.

  1. Engage the wire harness clamp.



    C206646
  1. Install the No. 1 parking brake cable assembly with the 5 bolts and nut.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Engage the clamp.



    C209223E02
  1. Temporarily install the lock nut.
    Text in Illustration 
    *1
    Lock Nut

    HINT:
    After adjusting parking brake pedal travel, tighten the lock nut.



2. CONNECT NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    C206650E01
  1. Connect the No. 1 parking brake pull rod sub-assembly to the parking brake control pedal assembly as shown in the illustration.
    Text in Illustration 
    *1
    Turn
    *2
    Hold

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



3. INSTALL NO. 3 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY


    C206643
  1. Install the No. 3 belt anchor reinforcement sub-assembly with the 4 bolts.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



4. INSTALL NO. 2 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY


    C206642
  1. Install the No. 2 belt anchor reinforcement sub-assembly with the 4 bolts.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



5. INSTALL FRONT SEAT ASSEMBLY LH

HINT:
Refer to the instructions for Installation of the front seat assembly (Click here).



6. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



7. INSTALL AIR CONDITIONING UNIT

HINT:
Refer to the instructions for Installation of the air conditioning unit (Click here).



8. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Remove the lower instrument panel finish panel assembly .

  1. Completely release the parking brake pedal.



    C206641E01
  1. Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 11 notches at 300 N (31 kgf, 67.5 lbf)



    C206641E01
  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check whether the parking brake drags or not.

  1. Install the lower instrument panel finish panel assembly .



9. INSPECT BRAKE WARNING LIGHT
  1. When operating the parking brake pedal, check that the brake warning light illuminates.

    Standard:
    The brake warning light always illuminates at the first click.