Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL PUMP

FUEL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    A171478E05
  1. Install a new gasket onto the fuel tank.
    Text in Illustration 
    *1
    Gasket



    A152307E04
  1. Set the fuel suction tube assembly with pump and gauge to the fuel tank.
    Text in Illustration 
    *1
    Notch
    *2
    Protrusion

    NOTICE:
    Make sure that the fuel sender gauge arm does not bend.

  1. Align the protrusions of the fuel suction tube assembly with pump and gauge with the notches of the fuel tank.



2. INSTALL FUEL PUMP GAUGE RETAINER


    A217160E01
  1. While holding the fuel suction tube assembly with pump and gauge by hand to prevent it from tilting, align the mark on a new fuel pump gauge retainer with the start mark on the fuel tank and tighten the fuel pump gauge retainer 180° by hand.
    Text in Illustration 
    *1
    Start Mark
    *2
    Mark
    *3
    Front

    HINT:
    1. Check that there is no damage, dents, foreign matter or other defects on the threads of the fuel tank.



    A245426E01
  1. Temporarily install the SST plate and claws to the fuel pump gauge retainer.
    Text in Illustration 
    *1
    SST
    (Plate)
    *2
    SST
    (Claw)
    *3
    Rib

    SST
    09808-14030   (09808-01030, 09808-01040, 09808-01050)

    HINT:
    Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.

  1. While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

    HINT:
    Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

  1. Install the SST handle.



    A245428E01
  1. Tighten the fuel pump gauge retainer approximately 360° so that the mark on the retainer comes within the range shown in the illustration.
    Text in Illustration 
    *1
    SST
    (Handle)
    *2
    SST
    (Plate)
    *3
    SST
    (Claw)
    *4
    Mark
    *a
    Front Side

    SST
    09808-14030   (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Do not press down on SST excessively as this may make the retainer hard to rotate, and may damage components.
    3. Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.
    4. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    5. If SST comes off of the retainer, loosen the SST bolts and reinstall SST.

    HINT:
    1. Lightly press down on SST to prevent it from separating from the retainer. While pressing SST, rotate the handle slowly to tighten the retainer.
    2. The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.



3. CONNECT FUEL TANK EVAPORATION TUBE


    A161746E01
  1. Connect the fuel tank evaporation tube to the fuel suction tube assembly.
    Text in Illustration 
    *1
    Retainer



4. CONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE


    A167459
  1. Connect the No. 1 charcoal canister outlet hose to the fuel suction tube assembly.

    HINT:
    After connecting the No. 2 fuel tank evaporation tube and No. 1 charcoal canister outlet hose, check that the No. 2 fuel tank evaporation tube is positioned below the No. 1 charcoal canister outlet hose.



5. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    A167460E01
  1. Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube assembly with the clip.



6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A217162E02
  1. Push the fuel tube joint in the plug of the fuel suction plate, then install the tube joint clip.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Tube Joint
    *3
    O-ring
    *4
    Collar
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube joint and plug before performing this work.
    2. Check that the fuel tube joint is securely inserted to the end.
    3. Check that the tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tank main tube cannot be pulled out.



    A217140
  1. Connect the fuel pump connector.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

      NOTICE:
      Do not start the engine.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

    5. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



9. INSTALL REAR FLOOR SERVICE HOLE COVER


    A216406
  1. Install the rear floor service hole cover with new butyl tape.



10. INSTALL REAR SEAT CUSHION ASSEMBLY


    B229993E01
  1. Engage the 2 guides of the seat cushion to the seatback.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Guide
    *3
    Hook

  1. Engage the 2 front hooks of the seat cushion to the vehicle body.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

    HINT:
    Confirm that the seat cushion is firmly installed.



11. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



12. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



13. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.