Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A82-123    Hybrid Battery Pack Cooling Fan 1

for Preparation Click here


DESCRIPTION

  1. Refer to the circuit description for DTC P0A84-123 .

DTC No.
DTC Detection Condition
Trouble Area
P0A82-123
The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
  1. Battery cooling blower assembly
  2. Battery smart unit
  3. Power management control ECU
  4. HV battery intake duct
  5. Wire harness or connector

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

1.CHECK FOR DTCS (DTC P0AFC-123 IS OUTPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART
A


2.CHECK DUCT AND BLOWER
  1. Remove the upper hybrid battery cover sub-assembly (Click here).



    A217830E01
  1. Check that the No. 1 hybrid battery intake duct and battery cooling blower are not disconnected, damaged, or clogged with foreign objects, and that the acoustical materials have not peeled.

    OK:
    The duct and blower are not disconnected, damaged, or clogged with foreign objects and the acoustical materials have not peeled.

    Text in Illustration 
    *1
    No. 1 Hybrid Battery Intake Duct

  1. Install the upper hybrid battery cover sub-assembly (Click here).



NG
CORRECT THE PROBLEM
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect the A21 connector from the power management control ECU (Click here).

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217834
  1. Disconnect the S14 connector from the battery cooling blower assembly.



    A217831E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Specified Condition
    S14-3 (SI0) or A21-29 (SI0) - Body ground
    10 kΩ or higher
    S14-3 (SI0) - A21-29 (SI0)
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)
    *2
    Rear view of wire harness connector
    (Power Management Control ECU)

  1. Connect the S14 connector to the battery cooling blower assembly.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the A21 connector to the power management control ECU (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK)
  1. Remove the power management control ECU (Click here).



    A217832E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A21-29 (SI0) - L5-5 (E01)
    10 kΩ or higher
    A21-29 (SI0) - L6-5 (E02)
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (to Power Management Control ECU)

  1. Install the power management control ECU (Click here).



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


5.READ VALUE USING INTELLIGENT TESTER
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

    NOTICE:
    If the active test cannot be performed, skip it and proceed to the next step to check voltage. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

  1. Enter the following menus: All Data / VMF Fan Motor Voltage 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" active test to operate the battery cooling blower assembly.



    A217833E01
  1. While the cooling fan is operating, compare the value in the data list (VMF Fan Motor Voltage 1) with the voltage value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    S14-2 (VM0) - S14-4 (GND0)
    Battery cooling blower is operating
    Difference between the value in the Data List (VMF Fan Motor Voltage 1) and the actual measurement value is 1 V or less.

    Text in Illustration 
    *1
    Component with harness connected
    (Battery Cooling Blower assembly)

HINT:
Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



NG
REPLACE BATTERY SMART UNIT (Click here)
OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)