DTC P3011-123 Battery Block 1 Becomes Weak |
DTC P3012-123 Battery Block 2 Becomes Weak |
DTC P3013-123 Battery Block 3 Becomes Weak |
DTC P3014-123 Battery Block 4 Becomes Weak |
DTC P3015-123 Battery Block 5 Becomes Weak |
DTC P3016-123 Battery Block 6 Becomes Weak |
DTC P3017-123 Battery Block 7 Becomes Weak |
DTC P3018-123 Battery Block 8 Becomes Weak |
DTC P3019-123 Battery Block 9 Becomes Weak |
DTC P3020-123 Battery Block 10 Becomes Weak |
DTC P3021-123 Battery Block 11 Becomes Weak |
DTC P3022-123 Battery Block 12 Becomes Weak |
DTC P3023-123 Battery Block 13 Becomes Weak |
DTC P3024-123 Battery Block 14 Becomes Weak |
| DTC No. | DTC Detection Condition | Trouble Area |
| P3011-123 P3012-123 P3013-123 P3014-123 | Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection). |
|
| P3015-123 | Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection). |
|
| P3016-123 P3017-123 P3018-123 P3019-123 P3020-123 P3021-123 P3022-123 P3023-123 P3024-123 | Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection). |
|
| 1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs (Click here).
| Result | Proceed to |
| P0AFC-123 is not output. | A |
| P0AFC-123 is also output. | B |
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (VB1 - VB14) |
Ensure the safety of the areas in front and at the back of the vehicle.
Apply the parking brake and secure the wheels using chocks.
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Fully warm up the engine and turn the air conditioning off.
Enter the following menus: Powertrain / Hybrid Control / Data List / Battery block Vol -V01 to V14.
Firmly depress the brake pedal with your left foot.
Move the select lever to D.
Record each battery block voltage from the data list (Battery block Vol -V01 to V14) while fully depressing the accelerator pedal.
Compare the battery block voltages (Battery block Vol - V01 to V14) between the even and odd number groups in each combination shown in the table below.
| Circuit A Battery Block | Circuit B Battery Block | Condition |
| Battery Block Vol-V01 (VB1) | Battery Block Vol-V02 (VB2) | "Battery Block Vol - V01" - "Battery Block Vol - V02" = 0.3 V or more |
| Battery Block Vol-V04 (VB4) | Battery Block Vol-V03 (VB3) | "Battery Block Vol - V04" - "Battery Block Vol - V03" = 0.3 V or more |
| Battery Block Vol-V05 (VB5) | Battery Block Vol-V06 (VB6) | "Battery Block Vol - V05" - "Battery Block Vol - V06" = 0.3 V or more |
| Battery Block Vol-V08 (VB8) | Battery Block Vol-V07 (VB7) | "Battery Block Vol - V08" - "Battery Block Vol - V07" = 0.3 V or more |
| Battery Block Vol-V09 (VB9) | Battery Block Vol-V10 (VB10) | "Battery Block Vol - V09" - "Battery Block Vol - V10" = 0.3 V or more |
| Battery Block Vol-V12 (VB12) | Battery Block Vol-V11 (VB11) | "Battery Block Vol - V12" - "Battery Block Vol - V11" = 0.3 V or more |
| Battery Block Vol-V13 (VB13) | Battery Block Vol-V14 (VB14) | "Battery Block Vol - V13" - "Battery Block Vol - V14" = 0.3 V or more |
| Circuit A Battery Block | Circuit B Battery Block | Condition |
| Battery Block Vol-V01 (VB1) | Battery Block Vol-V02 (VB2) | "Battery Block Vol - V02" - "Battery Block Vol - V01" = 0.3 V or more |
| Battery Block Vol-V04 (VB4) | Battery Block Vol-V03 (VB3) | "Battery Block Vol - V03" - "Battery Block Vol - V04" = 0.3 V or more |
| Battery Block Vol-V05 (VB5) | Battery Block Vol-V06 (VB6) | "Battery Block Vol - V06" - "Battery Block Vol - V05" = 0.3 V or more |
| Battery Block Vol-V08 (VB8) | Battery Block Vol-V07 (VB7) | "Battery Block Vol - V07" - "Battery Block Vol - V08" = 0.3 V or more |
| Battery Block Vol-V09 (VB9) | Battery Block Vol-V10 (VB10) | "Battery Block Vol - V10" - "Battery Block Vol - V09" = 0.3 V or more |
| Battery Block Vol-V12 (VB12) | Battery Block Vol-V11 (VB11) | "Battery Block Vol - V11" - "Battery Block Vol - V12" = 0.3 V or more |
| Battery Block Vol-V13 (VB13) | Battery Block Vol-V14 (VB14) | "Battery Block Vol - V14" - "Battery Block Vol - V13" = 0.3 V or more |

| Result | Proceed to |
| All conditions in table 1 are met. | A |
| All conditions in table 2 are met. | |
| Other than above. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | ||
| ||
| 3.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
| DTC P3015-123 is output. | A |
| DTC P3015-123 is not output. | B |
Turn the power switch off.
|
| ||||
| A | ||
| ||