Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P3011-123    Battery Block 1 Becomes Weak

DTC    P3012-123    Battery Block 2 Becomes Weak

DTC    P3013-123    Battery Block 3 Becomes Weak

DTC    P3014-123    Battery Block 4 Becomes Weak

DTC    P3015-123    Battery Block 5 Becomes Weak

DTC    P3016-123    Battery Block 6 Becomes Weak

DTC    P3017-123    Battery Block 7 Becomes Weak

DTC    P3018-123    Battery Block 8 Becomes Weak

DTC    P3019-123    Battery Block 9 Becomes Weak

DTC    P3020-123    Battery Block 10 Becomes Weak

DTC    P3021-123    Battery Block 11 Becomes Weak

DTC    P3022-123    Battery Block 12 Becomes Weak

DTC    P3023-123    Battery Block 13 Becomes Weak

DTC    P3024-123    Battery Block 14 Becomes Weak

for Preparation Click here


DESCRIPTION

  1. Refer to the Description for DTC P0A80-123 .

DTC No.
DTC Detection Condition
Trouble Area
P3011-123
P3012-123
P3013-123
P3014-123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. HV battery assembly
  2. Battery smart unit
P3015-123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. HV battery assembly
  2. Battery smart unit
  3. Service plug grip
P3016-123
P3017-123
P3018-123
P3019-123
P3020-123
P3021-123
P3022-123
P3023-123
P3024-123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. HV battery assembly
  2. Battery smart unit

HINT:
P3011-123 to P3024-123 will not be set unless the vehicle is driven for approximately 10 minutes after clearing the DTCs.


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART
A


2.READ VALUE USING INTELLIGENT TESTER (VB1 - VB14)
  1. Ensure the safety of the areas in front and at the back of the vehicle.

  1. Apply the parking brake and secure the wheels using chocks.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Fully warm up the engine and turn the air conditioning off.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery block Vol -V01 to V14.

  1. Firmly depress the brake pedal with your left foot.

  1. Move the select lever to D.

  1. Record each battery block voltage from the data list (Battery block Vol -V01 to V14) while fully depressing the accelerator pedal.

  1. Compare the battery block voltages (Battery block Vol - V01 to V14) between the even and odd number groups in each combination shown in the table below.


Table 1 
Circuit A Battery Block
Circuit B Battery Block
Condition
Battery Block Vol-V01 (VB1)
Battery Block Vol-V02 (VB2)
"Battery Block Vol - V01" - "Battery Block Vol - V02" = 0.3 V or more
Battery Block Vol-V04 (VB4)
Battery Block Vol-V03 (VB3)
"Battery Block Vol - V04" - "Battery Block Vol - V03" = 0.3 V or more
Battery Block Vol-V05 (VB5)
Battery Block Vol-V06 (VB6)
"Battery Block Vol - V05" - "Battery Block Vol - V06" = 0.3 V or more
Battery Block Vol-V08 (VB8)
Battery Block Vol-V07 (VB7)
"Battery Block Vol - V08" - "Battery Block Vol - V07" = 0.3 V or more
Battery Block Vol-V09 (VB9)
Battery Block Vol-V10 (VB10)
"Battery Block Vol - V09" - "Battery Block Vol - V10" = 0.3 V or more
Battery Block Vol-V12 (VB12)
Battery Block Vol-V11 (VB11)
"Battery Block Vol - V12" - "Battery Block Vol - V11" = 0.3 V or more
Battery Block Vol-V13 (VB13)
Battery Block Vol-V14 (VB14)
"Battery Block Vol - V13" - "Battery Block Vol - V14" = 0.3 V or more

Table 2 
Circuit A Battery Block
Circuit B Battery Block
Condition
Battery Block Vol-V01 (VB1)
Battery Block Vol-V02 (VB2)
"Battery Block Vol - V02" - "Battery Block Vol - V01" = 0.3 V or more
Battery Block Vol-V04 (VB4)
Battery Block Vol-V03 (VB3)
"Battery Block Vol - V03" - "Battery Block Vol - V04" = 0.3 V or more
Battery Block Vol-V05 (VB5)
Battery Block Vol-V06 (VB6)
"Battery Block Vol - V06" - "Battery Block Vol - V05" = 0.3 V or more
Battery Block Vol-V08 (VB8)
Battery Block Vol-V07 (VB7)
"Battery Block Vol - V07" - "Battery Block Vol - V08" = 0.3 V or more
Battery Block Vol-V09 (VB9)
Battery Block Vol-V10 (VB10)
"Battery Block Vol - V10" - "Battery Block Vol - V09" = 0.3 V or more
Battery Block Vol-V12 (VB12)
Battery Block Vol-V11 (VB11)
"Battery Block Vol - V11" - "Battery Block Vol - V12" = 0.3 V or more
Battery Block Vol-V13 (VB13)
Battery Block Vol-V14 (VB14)
"Battery Block Vol - V14" - "Battery Block Vol - V13" = 0.3 V or more

A298786E03

HINT:
When an internal malfunction occurs in the battery smart unit, this symptom (difference in voltage of 0.3 V or more for all 7 pairs of blocks) will occur.

Result:
Result
Proceed to
All conditions in table 1 are met.
A
All conditions in table 2 are met.
Other than above.
B

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



B
Go to step 3
A

REPLACE BATTERY SMART UNIT (Click here)  

3.CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P3015-123 is output.
    A
    DTC P3015-123 is not output.
    B

  1. Turn the power switch off.



B
REPLACE HV BATTERY ASSEMBLY (Click here)
A

REPLACE SERVICE PLUG GRIP AND HV BATTERY ASSEMBLY (Click here)