Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0AAE-123    Hybrid Battery Pack Air Temperature Sensor "A" Circuit Low

DTC    P0AAF-123    Hybrid Battery Pack Air Temperature Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

  1. The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensor . The battery smart unit uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.

DTC No.
DTC Detection Condition
Trouble Area
P0AAE-123
P0AAF-123
When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open circuit) or is higher than a predetermined limit (short circuit)
  1. Hybrid battery thermistor
  2. Battery smart unit
  3. Wire harness or connector
  4. Hybrid battery junction block

HINT:
After confirming that DTC P0AAE-123 or P0AAF-123 is output, use the intelligent tester to check "Inhaling Air Temp" in the HV ECU data list.


Displayed Temperature
Malfunction
-45°C (-49°F) or less
Open or +B short circuit
95°C (203°F) or more
GND short

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9D-123 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

1.CHECK FOR DTCS (DTC P0AFC-123 IS OUTPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART
A


2.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



  1. Check installation of inlet air temperature sensor



      A217836E06
    1. Check the connections of the z17 connector of the battery smart unit.

      OK:
      The connectors are connected securely and there are no contact problems.

      Result:
      Result
      Proceed to
      NG
      B
      OK
      Go to next step

      Text in Illustration 
      *1
      Battery Smart Unit



    2. A219389
    3. Visually check the installation condition of the inlet air temperature sensor.

      OK:
      The inlet air temperature sensor is installed in the correct location and its claws are engaged securely.

      Result:
      Result
      Proceed to
      The inlet air temperature sensor is installed in the correct location and its claws are engaged securely
      A
      Claws are damaged.
      C
      Inlet air temperature sensor is not installed correctly, but claws are not damaged.
      D

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



B
CONNECT SECURELY

C
REPLACE HYBRID BATTERY THERMISTOR (Click here)

D
INSTALL PARTS CORRECTLY
A


3.CHECK HYBRID BATTERY THERMISTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E01
  1. Disconnect the c1 and z17 connectors from the battery smart unit.



    A216735E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z17-1 (TC0) - z17-7 (GC0)
    0°C (32°F)
    26.7 to 27.8 kΩ
    25°C (77°F)
    9.9 to 10.1 kΩ
    40°C (104°F)
    5.73 to 5.92 kΩ

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Battery Smart Unit)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z17-1 (TC0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-1 (TC0) - c1-8 (GND)
    Power switch off
    10 kΩ or higher
    z17-7 (GC0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-7 (GC0) - c1-8 (GND)
    Power switch off
    10 kΩ or higher

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z17-6 (TB0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-6 (TB0) - c1-8 (GND)
    Power switch off
    10 kΩ or higher
    z17-12 (GB0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-12 (GB0) - c1-8 (GND)
    Power switch off
    10 kΩ or higher
    z17-5 (TB1) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-5 (TB1) - c1-8 (GND)
    Power switch off
    10 kΩ or higher
    z17-11 (GB1) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-11 (GB1) - c1-8 (GND)
    Power switch off
    10 kΩ or higher
    z17-4 (TB2) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-4 (TB2) - c1-8 (GND)
    Power switch off
    10 kΩ or higher
    z17-10 (GB2) - c1-4 (IGCT)
    Power switch off
    10 kΩ or higher
    z17-10 (GB2) - c1-8 (GND)
    Power switch off
    10 kΩ or higher

  1. Connect the c1 and z17 connectors to the battery smart unit.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
Go to step 7
OK


4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set. Use the intelligent tester to clear the DTCs (Click here).



    A214447E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-5 (VIB) - c1-6 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *1
    Component with harness connected
    (Battery Smart Unit)

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
Go to step 5
OK

REPLACE BATTERY SMART UNIT (Click here)  

5.CHECK HYBRID BATTERY JUNCTION BLOCK

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the HV relay assembly (battery current sensor) connector disconnected causes DTC P0AC2-123 to be set. Use the intelligent tester to clear the DTCs (Click here).



    A221326E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c4-1 (VIB) - c4-2 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Turn the power switch off.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



NG
Go to step 6
OK

REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)  

6.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E03
  1. Disconnect only the c1 connector of the battery smart unit.

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.



    A221325E01
  1. Measure the resistance according to the value(s) in the tables below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) - c4-3 (IB)
    Power switch off
    Below 1 Ω
    c1-6 (GIB) - c4-2 (GIB)
    Power switch off
    Below 1 Ω
    c1-5 (VIB) - c4-1 (VIB)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) or c4-3 (IB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-6 (GIB) or c4-2 (GIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-5 (VIB) or c4-1 (VIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Battery Smart Unit)
    *2
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Connect the c1 connector to the battery smart unit.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BATTERY SMART UNIT (Click here)  

7.CHECK HARNESS AND CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).

  1. Check the wire harness and connectors of the battery temperature sensor and inlet air temperature sensor for abnormalities by sight and touch.

    Specified Condition:
    There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.

  1. Install the upper hybrid battery cover sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR HARNESS OR CONNECTOR
OK

REPLACE HYBRID BATTERY THERMISTOR (Click here)