Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B231709E14


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 3 connectors
*B
for LHD
*C
for RHD
-
-
*1
Main body ECU (multiplex network body ECU)
*2
3 connectors
  1. Disconnect the 2A, 2B, 2C, 2E*1, 2F*2 and L8 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-43 - Body ground
    G - Body ground
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    Power switch off
    Below 1 V
    2B-25 - Body ground
    B - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    2C-18 (BECU) - Body ground
    Y - Body ground
    Battery power supply
    Always
    11 to 14 V
    2E-1*1 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    2F-1*2 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-6 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L8-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the 2A, 2B, 2C, 2E*1, 2F*2 and L8 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-52 (ILE) - Body ground
    L - Body ground
    Interior lights drive output
    Interior lights off
    11 to 14 V
    Interior lights on
    Below 1 V
    2B-17 (FSPT) - Body ground
    L - Body ground
    Front passenger footwell light drive output
    Front passenger footwell light off
    11 to 14 V
    Front passenger footwell light on
    Below 1 V
    2B-18 (FSPT) - Body ground
    L - Body ground
    Driver footwell light drive output
    Driver footwell light off
    11 to 14 V
    Driver footwell light on
    Below 1 V
    2B-29 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch RH input
    Rear door RH and LH locked
    Pulse generation
    Rear door RH or LH unlocked
    Below 1 V
    2D-25 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch LH input
    Rear door LH and RH locked
    Pulse generation
    Rear door LH or RH unlocked
    Below 1 V
    2D-35 (FLCY) - Body ground
    V*1 - Body ground
    BR*2 - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    2D-36 (FRCY) - Body ground
    BR*1 - Body ground
    V*2 - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH or LH input
    Rear door RH or LH open
    Below 1 V
    Rear door RH and LH closed
    Pulse generation
    L7-7 (LSFL) - Body ground
    GR - Body ground
    Front door unlock detection switch LH input
    Front door LH locked
    Pulse generation
    Front door LH unlocked
    Below 1 V
    L7-18 (LSFR) - Body ground
    LG - Body ground
    Front door unlock detection RH switch input
    Front door RH locked
    Pulse generation
    Front door RH unlocked
    Below 1 V
    L7-19 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Back door closed and luggage compartment light switch off
    Pulse generation
    Back door closed and luggage compartment light switch on
    11 to 14 V

    HINT:
    *1: for LHD
    *2: for RHD

    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

E192848E16


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 1 connector
*B
for LHD
*C
for RHD
-
-
*1
Main body ECU (multiplex network body ECU)
*2
1 connector
  1. Disconnect the 2A, 2B, 2C, 2E*1 and 2F*2 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-43 - Body ground
    G - Body ground
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    Power switch off
    Below 1 V
    2B-25 - Body ground
    B - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    2C-18 (BECU) - Body ground
    Y - Body ground
    Battery power supply
    Always
    11 to 14 V
    2E-1*1 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    2F-1*2 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-6 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the 2A, 2B, 2C, 2E*1 and 2F*2 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-52 (ILE) - Body ground
    L - Body ground
    Interior lights drive output
    Interior lights off
    11 to 14 V
    Interior lights on
    Below 1 V
    2B-17 (FSPT) - Body ground
    L - Body ground
    Front passenger footwell light drive output
    Front passenger footwell light off
    11 to 14 V
    Front passenger footwell light on
    Below 1 V
    2B-18 (FSPT) - Body ground
    L - Body ground
    Driver footwell light drive output
    Driver footwell light off
    11 to 14 V
    Driver footwell light on
    Below 1 V
    2B-29 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch RH input
    Rear door RH and LH locked
    Pulse generation
    Rear door RH or LH unlocked
    Below 1 V
    2D-25 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch LH input
    Rear door LH and RH locked
    Pulse generation
    Rear door LH or RH unlocked
    Below 1 V
    2D-35 (FLCY) - Body ground
    V*1 - Body ground
    BR*2 - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    2D-36 (FRCY) - Body ground
    BR*1 - Body ground
    V*2 - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH or LH input
    Rear door RH or LH open
    Below 1 V
    Rear door RH and LH closed
    Pulse generation
    L7-7 (LSFL) - Body ground
    GR - Body ground
    Front door unlock detection switch LH input
    Front door LH locked
    Pulse generation
    Front door LH unlocked
    Below 1 V
    L7-18 (LSFR) - Body ground
    LG - Body ground
    Front door unlock detection RH switch input
    Front door RH locked
    Pulse generation
    Front door RH unlocked
    Below 1 V
    L7-19 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Back door closed and luggage compartment light switch off
    Pulse generation
    Back door closed and luggage compartment light switch on
    11 to 14 V

    HINT:
    *1: for LHD
    *2: for RHD

    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the L62 certification ECU (smart key ECU assembly) connector.


    B203498E15

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the L62 certification ECU (smart key ECU assembly) connector.

  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-11 (SWIL) - Body ground
    G - Body ground
    Power switch illumination drive output
    Power switch illumination on
    11 to 14 V or pulse generation
    Power switch illumination off
    Below 1 V
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.