Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1516    Torque Sensor Zero Point Adjustment Incomplete

DTC    C1526    Rotation Angle Sensor Initialization Incomplete

for Preparation Click here


DESCRIPTION

These DTCs do not indicate a malfunction. The power steering ECU assembly outputs these DTCs when it determines that the rotation angle sensor initialization and torque sensor zero point calibration are incomplete.

DTC No.
DTC Detection Condition
Trouble Area
C1516
Torque sensor zero point calibration is incomplete due to the steering wheel being touched during calibration.
There is no malfunction if this DTC is not output again after clearing the DTCs and torque sensor calibration, and performing zero point calibration.
C1526
Rotation angle sensor initialization is incomplete due to the steering wheel being touched during calibration.
There is no malfunction if this DTC is not output again after clearing the DTCs and torque sensor calibration, and performing rotation angle sensor initialization.

INSPECTION PROCEDURE

NOTICE:
  1. If the power steering ECU assembly has been replaced with a new one, perform rotation angle sensor initialization and torque sensor zero point calibration (Click here).
  2. If the electric power steering column sub-assembly or power steering motor assembly has been replaced, perform rotation angle sensor initialization and torque sensor zero point calibration (Click here).

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT
  1. Initialize rotation angle sensor and calibrate torque sensor zero point (Click here).


NEXT


3.CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result:
    Condition
    Proceed to
    DTCs are still output after performing rotation angle sensor initialization and steering zero point calibration 3 times*1.
    A
    DTCs are still output even after performing rotation angle sensor initialization and steering zero point calibration once or twice*2.
    B
    Normal system code is output.
    C

    HINT:
    1. *1: The power steering ECU assembly must be replaced if DTC C1516 or C1526 is still output even after the rotation angle sensor initialization and torque sensor zero point calibration is performed 3 times.
    2. *2: Perform rotation angle sensor initialization and torque sensor zero point calibration again if DTC C1516 or C1526 is still output even after the rotation angle sensor initialization and calibration is performed once or twice.



B
PERFORM ROTATION ANGLE SENSOR INITIALIZATION AND ZERO POINT CALIBRATION AGAIN (Click here)

C
END
A


4.REPLACE POWER STEERING ECU ASSEMBLY
  1. Replace the power steering ECU assembly (Click here).


NEXT


5.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT
  1. Initialize rotation angle sensor and calibrate torque sensor zero point (Click here).


NEXT


7.CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result:
    Condition
    Proceed to
    DTC C1516 are still output after performing rotation angle sensor initialization and steering zero point calibration 3 times*1.
    A
    DTC C1526 are still output after performing rotation angle sensor initialization and steering zero point calibration 3 times*2.
    B
    DTCs are still output even after performing rotation angle sensor initialization and steering zero point calibration twice*3.
    C
    Normal system code is output.
    D

    HINT:
    1. *1: The electric power steering column sub-assembly must be replaced if DTC C1516 is still output even after the rotation angle sensor initialization and torque sensor zero point calibration is performed 3 times.
    2. *2: The electric power steering column sub-assembly must be replaced if DTC C1526 is still output even after the rotation angle sensor initialization and torque sensor zero point calibration is performed 3 times.
    3. *3: Perform rotation angle sensor initialization and torque sensor zero point calibration again if DTC C1516 or C1526 is still output even after the rotation angle sensor initialization and calibration is performed twice.



B
REPLACE POWER STEERING MOTOR ASSEMBLY

C
PERFORM ROTATION ANGLE SENSOR INITIALIZATION AND ZERO POINT CALIBRATION AGAIN (Click here)

D
END
A

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)