Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A9D-123    Hybrid Battery Temperature Sensor "A" Circuit Low

DTC    P0A9E-123    Hybrid Battery Temperature Sensor "A" Circuit High

DTC    P0AC7-123    Hybrid Battery Temperature Sensor "B" Circuit Low

DTC    P0AC8-123    Hybrid Battery Temperature Sensor "B" Circuit High

DTC    P0ACC-123    Hybrid Battery Temperature Sensor "C" Circuit Low

DTC    P0ACD-123    Hybrid Battery Temperature Sensor "C" Circuit High

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P0A9C-123 .

DTC No.
DTC Detection Condition
Trouble Area
P0A9D-123
P0A9E-123
P0AC7-123
P0AC8-123
P0ACC-123
P0ACD-123
When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
  1. Hybrid battery thermistor
  2. Battery smart unit
  3. Wire harness or connector
  4. Hybrid battery junction block

HINT:
After confirming that a DTC is output, use the intelligent tester to check "Temp of BATT TB 1 to 3" in the hybrid vehicle control system ECU data list.

Temperature Displayed
Malfunction
Below -45°C (-49°F)
Open or +B short circuit
95°C (203°F) or more
GND short circuit

WIRING DIAGRAM


A219394E07


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART
A


2.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 1 to 3.

    HINT:
    Compare the temperature of the 3 battery temperature sensors to determine the sensor with the malfunction (Temp of Batt TB1 to TB3).


NEXT


3.CHECK CONNECTOR CONNECTION CONDITION

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E02
  1. Check the connections of the z17 connector of the battery smart unit.

    OK:
    The connectors are connected securely and there are no contact problems.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
CONNECT SECURELY
OK


4.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E01
  1. Disconnect the z17 and c1 connectors of the battery smart unit.



    A216736E01
  1. Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).
    Tester Connection 
    Tester Connection
    Battery Temperature Sensor No.
    z17-6 (TB0) - z17-12 (GB0)
    0
    z17-5 (TB1) - z17-11 (GB1)
    1
    z17-4 (TB2) - z17-10 (GB2)
    2
    Standard Resistance 
    Thermistor Temperature
    Switch Condition
    Specified Condition
    0°C (32°F)
    Power switch off
    26.7 to 27.8 kΩ
    25°C (77°F)
    Power switch off
    9.9 to 10.1 kΩ
    40°C (104°F)
    Power switch off
    5.73 to 5.92 kΩ
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Battery Smart Unit)



    A216735E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Standard Resistance
    z17-6 (TB0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-6 (TB0) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-12 (GB0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-12 (GB0) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-5 (TB1) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-5 (TB1) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-11 (GB1) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-11 (GB1) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-4 (TB2) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-4 (TB2) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-10 (GB2) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-10 (GB2) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-1 (TC0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-1 (TC0) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-7 (GC0) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-7 (GC0) - c1-8 (GND)
    Power switch off
    10 kΩ or more

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Battery Smart Unit)

  1. Connect the z17 and c1 connectors of the battery smart unit.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
Go to step 8
OK


5.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set. Use the intelligent tester to clear the DTCs (Click here).



    A214447E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-5 (VIB) - c1-6 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *1
    Component with harness connected
    (Battery Smart Unit)

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
Go to step 6
OK

REPLACE BATTERY SMART UNIT (Click here)  

6.CHECK HYBRID BATTERY JUNCTION BLOCK

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the HV relay assembly (battery current sensor) connector disconnected causes DTC P0AC2-123 to be set. Use the intelligent tester to clear the DTCs (Click here).



    A221326E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c4-1 (VIB) - c4-2 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Turn the power switch off.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



NG
Go to step 7
OK

REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)  

7.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E03
  1. Disconnect only the c1 connector of the battery smart unit.

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.



    A221325E01
  1. Measure the resistance according to the value(s) in the tables below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) - c4-3 (IB)
    Power switch off
    Below 1 Ω
    c1-6 (GIB) - c4-2 (GIB)
    Power switch off
    Below 1 Ω
    c1-5 (VIB) - c4-1 (VIB)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) or c4-3 (IB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-6 (GIB) or c4-2 (GIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-5 (VIB) or c4-1 (VIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Battery Smart Unit)
    *2
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Connect the c1 connector to the battery smart unit.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BATTERY SMART UNIT (Click here)  

8.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).

  1. Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

    Specified Condition:
    There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.

  1. Install the upper hybrid battery cover sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID BATTERY THERMISTOR (Click here)