Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR

STEERING GEAR > INSTALLATION

for Preparation Click here



1. INSTALL TIE ROD END SUB-ASSEMBLY LH


    C187022E02
  1. Install the lock nut and tie rod end sub-assembly LH to the steering gear assembly until the matchmarks are aligned.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    After adjusting the toe-in, tighten the lock nut.



2. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



3. INSTALL STEERING LINK ASSEMBLY


    C152552
  1. Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 nuts.

    NOTICE:
    1. Keep the nut from rotating while turning the bolt because the nut has its own stopper.
    2. Make sure to tighten the bolts starting from the left side of the vehicle.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



4. INSTALL STEERING INTERMEDIATE SHAFT


    C208471E01
  1. Align the matchmarks and install the steering intermediate shaft to the steering link assembly.
    Text in Illustration 
    *1
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



5. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C208472
  1. Align the round hole in the No. 1 steering column hole cover sub-assembly with the protrusion of the steering link assembly to install the cover.



6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C205602
  1. Support the front suspension crossmember with a transmission jack.



  1. While inserting SST into the reference holes on the front suspension crossmember RH and LH alternately, tighten 2 bolts A, 2 bolts B, C and 2 nuts on the RH and LH sides to the respective specified torque in several steps.


    C206981E01

    SST
    09670-00020  

    Torque:
    Bolt A:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }
    Bolt B, C, Nut D, E:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Temporarily tighten bolt B, and then fully tighten the 2 bolts and 2 nuts in the order of C, E, D, and B.



    C205596
  1. Install the 2 wire harness clamp brackets with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



7. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH


    C234406E01
  1. Install the front suspension member rear brace LH with the 2 bolts B and bolt A.

    Torque:
    Bolt A:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }
    Bolt B :
    93 N*m{ 948 kgf*cm , 69 ft.*lbf }

  1. Install the clip.



8. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:
Perform the same procedure as for the LH side.



9. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH


    C205598E01
  1. Install the rear side rail reinforcement sub-assembly LH with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }

    NOTICE:
    Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.



10. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



11. INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT


    C154783
  1. Install the front engine mounting bracket lower reinforcement with the 2 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }



12. CONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    C205578
  1. Install the front No. 1 lower suspension arm sub-assembly to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    89 N*m{ 908 kgf*cm , 66 ft.*lbf }



13. CONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



14. CONNECT TIE ROD END SUB-ASSEMBLY LH


    C151407
  1. Connect the tie rod end sub-assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    Further tighten the nut up to 60° if the holes for the clip are not aligned.

  1. Install a new clip.



15. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



16. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


    C205594
  1. Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



17. CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



18. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


C152549E04
  1. Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Make sure that the lips of the No. 1 steering column hole cover sub-assembly are not damaged.



19. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C206262E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
    Text in Illustration 
    *1
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



20. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


21. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C206261
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



22. INSTALL REAR ENGINE UNDER COVER LH


23. INSTALL REAR ENGINE UNDER COVER RH

HINT:
Perform the same procedure as for the LH side.



24. INSTALL FRONT NO. 3 ENGINE UNDER COVER


25. INSTALL NO. 2 ENGINE UNDER COVER


26. INSTALL NO. 1 ENGINE UNDER COVER


27. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



28. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.



29. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).