STEERING GEAR > INSTALLATION |
| 1. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() |
Install the lock nut and tie rod end sub-assembly LH to the steering gear assembly until the matchmarks are aligned.
| *1 | Matchmark |
| 2. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 3. INSTALL STEERING LINK ASSEMBLY |
![]() |
Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 nuts.
| 4. INSTALL STEERING INTERMEDIATE SHAFT |
![]() |
Align the matchmarks and install the steering intermediate shaft to the steering link assembly.
| *1 | Matchmark |
Install the bolt.
| 5. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Align the round hole in the No. 1 steering column hole cover sub-assembly with the protrusion of the steering link assembly to install the cover.
| 6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Support the front suspension crossmember with a transmission jack.
While inserting SST into the reference holes on the front suspension crossmember RH and LH alternately, tighten 2 bolts A, 2 bolts B, C and 2 nuts on the RH and LH sides to the respective specified torque in several steps.

![]() |
Install the 2 wire harness clamp brackets with the 2 bolts.
| 7. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH |
![]() |
Install the front suspension member rear brace LH with the 2 bolts B and bolt A.
Install the clip.
| 8. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH |
| 9. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
![]() |
Install the rear side rail reinforcement sub-assembly LH with the 4 bolts.
| 10. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH |
| 11. INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT |
![]() |
Install the front engine mounting bracket lower reinforcement with the 2 bolts.
| 12. CONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Install the front No. 1 lower suspension arm sub-assembly to the front lower ball joint with the bolt and 2 nuts.
| 13. CONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH |
| 14. CONNECT TIE ROD END SUB-ASSEMBLY LH |
![]() |
Connect the tie rod end sub-assembly LH to the steering knuckle with the nut.
Install a new clip.
| 15. CONNECT TIE ROD END SUB-ASSEMBLY RH |
| 16. CONNECT FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.
| 17. CONNECT FRONT STABILIZER LINK ASSEMBLY RH |
| 18. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
| *1 | Clip A |
| *2 | Clip B |
| 19. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
| *1 | Matchmark |
Install the bolt.
| 20. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 21. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 22. INSTALL REAR ENGINE UNDER COVER LH |
| 23. INSTALL REAR ENGINE UNDER COVER RH |
| 24. INSTALL FRONT NO. 3 ENGINE UNDER COVER |
| 25. INSTALL NO. 2 ENGINE UNDER COVER |
| 26. INSTALL NO. 1 ENGINE UNDER COVER |
| 27. INSTALL FRONT WHEELS |
| 28. STABILIZE SUSPENSION |
Lower the vehicle.
Press down on the vehicle several times to stabilize the suspension.
| 29. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
Inspect and adjust the front wheel alignment (Click here).