Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR

STEERING GEAR > REMOVAL

for Preparation Click here



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. SECURE STEERING WHEEL


    C205164
  1. Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.



3. REMOVE COLUMN HOLE COVER SILENCER SHEET


    C206261
  1. Turn back the floor carpet.

  1. Remove the 2 clips and column hole cover silencer sheet.



4. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C206262E01
  1. Put matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Do not separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft.

  1. Remove the bolt.

  1. Separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft.



5. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C152549E04
  1. Remove clip A, detach clip B from the body and disconnect the No. 1 steering column hole cover sub-assembly.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Do not damage clips A and B.



6. REMOVE FRONT WHEELS


7. REMOVE NO. 1 ENGINE UNDER COVER


8. REMOVE NO. 2 ENGINE UNDER COVER


9. REMOVE FRONT NO. 3 ENGINE UNDER COVER


10. REMOVE REAR ENGINE UNDER COVER LH


11. REMOVE REAR ENGINE UNDER COVER RH

HINT:
Perform the same procedure as for the LH side.



12. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


C205594
  1. Remove the nut and separate the stabilizer link assembly LH from the front stabilizer bar.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



13. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



14. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the clip and nut.



    C157110E03
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the steering knuckle.


    C177185E08


    Text in Illustration 
    *1
    Turn
    *2
    Nut
    SST
    09960-20010   (09961-02010)

    CAUTION:
    Apply grease to the bolt threads and the tip of SST.

    NOTICE:
    1. Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.
    2. Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the front disc brake dust cover.
    5. Do not damage the ball joint dust cover.
    6. Do not damage the steering knuckle.



15. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



16. SEPARATE FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    C205578
  1. Remove the bolt and 2 nuts, and separate the front No. 1 lower suspension arm sub-assembly from the front lower ball joint.



17. SEPARATE FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



18. REMOVE FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT


    C205597
  1. Remove the 2 bolts and front engine mounting bracket lower reinforcement.



19. REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH


    C205598
  1. Remove the 4 bolts and rear side rail reinforcement sub-assembly LH.



20. REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



21. REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH


    C205599
  1. Remove the 3 bolts and front suspension member rear brace LH.



22. REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:
Perform the same procedure as for the LH side.



23. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C205596
  1. Remove the 2 bolts and 2 wire harness clamp brackets from the front suspension crossmember sub-assembly.



  1. Remove the 2 bolts and 2 nuts, and separate the front suspension crossmember sub-assembly from the rear engine mounting insulator.


    C205600



    C205602
  1. Using a transmission jack, support the front suspension crossmember sub-assembly.



  1. Remove the 2 bolts and front suspension crossmember sub-assembly.


    C205601



24. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C208470
  1. Remove the No. 1 steering column hole cover sub-assembly from the steering link assembly.



25. REMOVE STEERING INTERMEDIATE SHAFT


    C208471E01
  1. Put matchmarks on the steering intermediate shaft and steering link assembly.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the bolt and steering intermediate shaft from the steering link assembly.



26. REMOVE STEERING LINK ASSEMBLY


    C152552
  1. Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

    NOTICE:
    Keep the nut from rotating while turning the bolt because the nut has its own stopper.



27. SECURE STEERING LINK ASSEMBLY


    C153102E05
  1. Using SST, secure the steering link assembly in a vise.
    Text in Illustration 
    *1
    Protective Tape

    SST
    09612-00012  

    HINT:
    Tape SST before use.



28. REMOVE TIE ROD END SUB-ASSEMBLY LH


C187022E02
Text in Illustration 
*1
Matchmark
  1. Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.

  1. Remove the tie rod end sub-assembly LH and lock nut.



29. REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.