Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM

DTC    B2075    Passenger Side Seat Belt Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when there is a short or open in the front seat inner belt buckle switch circuit (for passenger side).

DTC No.
DTC Detection Condition
Trouble Area
B2075
Open or short in front seat inner belt (buckle switch) circuit
  1. Front seat inner belt (for passenger side)
  2. Seat belt control ECU
  3. Wire harness

WIRING DIAGRAM


E191219E07


E191219E06


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT LH - SEAT BELT CONTROL ECU)
E172285E06
  1. Disconnect the front seat inner belt LH connector.

  1. Disconnect the seat belt control ECU connector.

  1. Measure the resistance of the wire harness side connectors.
    Measure the resistance of the wire harness side connectors.

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    L3-4 (RBL+) - S22-5 (RBE+)
    Always
    Below 1 Ω
    L3-3 (RBL-) - S22-4 (RBE-)
    Always
    Below 1 Ω
    L3-4 (RBL+) or S22-5 (RBE-) - Body ground
    Always
    10 kΩ or higher
    L3-3 (RBL-) or S22-4 (RBE-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    L3-5 (LBL+) - R5-5 (LBE+)
    Always
    Below 1 Ω
    L3-6 (LBL-) - R5-4 (LBE-)
    Always
    Below 1 Ω
    L3-5 (LBL+) or R5-5 (LBE+) - Body ground
    Always
    10 kΩ or higher
    L3-6 (LBL-) or R5-4 (LBE-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Front Seat Inner Belt)
    *2
    Front view of wire harness connector
    (to Seat Belt Control ECU)
    *3
    for RHD
    *4
    for LHD

  1. Reconnect the seat belt control ECU connector.

  1. Reconnect the front seat inner belt connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT SEAT INNER BELT LH - SEAT BELT CONTROL ECU)
OK


2.CHECK SEAT BELT CONTROL ECU


    E192406E03
  1. Fasten the passenger side seat belt.

  1. Turn the power switch on (IG).

  1. Using an oscilloscope, check the waveform of the seat belt control ECU between the connector terminals.

    HINT:
    Voltage is only output for 10 ms of a 100 ms cycle.

    Item
    Contents
    Terminal
    L3-5 (LBL+)
    L3-6 (LBL-)
    L3-4 (RBL+)
    L3-3 (RBL-)
    Tool setting
    2 V/DIV, 20 ms/DIV
    Vehicle Condition
    Power switch on (IG)
    Text in Illustration 
    *1
    Seat Belt Control ECU

    OK:
    Approximately 5 V



NG
REPLACE FRONT SEAT INNER BELT (for Passenger Side)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)