Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0AFC-150    Hybrid Battery Pack Sensor Module

for Preparation Click here


DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC NO.
INF Code
DTC Detection Condition
Trouble Area
P0AFC
150
Power source voltage of the battery smart unit drops during precharge.
  1. Battery smart unit
  2. Wire harness or connector
  3. Fuse
  4. Relay

WIRING DIAGRAM


A220462E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
  1. Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
  2. After completing repairs, restart the system (turn the power switch on (READY)) and recheck for DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).



    A214447E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-4 (IGCT) - c1-8 (GND)
    Power switch on (IG)
    11 to 14 V

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
    2. Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set. Use the intelligent tester to clear the DTCs (Click here).

    Text in Illustration 
    *1
    Component with harness connected
    (Battery Smart Unit)

  1. Turn the power switch off.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



NG
Go to step 2
OK

REPLACE BATTERY SMART UNIT (Click here)  

2.CHECK FUSE (IGCT, IGCT NO. 2)


    A217826E01
  1. Remove the IGCT and IGCT No. 2 fuses from the engine room junction block assembly.
    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    IGCT Fuse
    *3
    IGCT No. 2 Fuse

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IGCT fuse
    Always
    Below 1 Ω
    IGCT No. 2 fuse
    Always
    Below 1 Ω

  1. Install the IGCT and IGCT No. 2 fuses to the engine room junction block assembly.



NG
REPLACE FUSE (IGCT, IGCT NO. 2)
OK


3.CHECK RELAY (IGCT)


    A217827E01
  1. Remove the IGCT relay from the engine room junction block assembly.
    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    IGCT Relay



    A111813E17
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Auxiliary battery voltage is applied between terminals 1 and 2
    10 kΩ or more
    Auxiliary battery voltage is not applied between terminals 1 and 2
    below 1 Ω

  1. Install the IGCT relay to the engine room junction block assembly.



NG
REPLACE RELAY (IGCT)
OK


4.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY SMART UNIT)

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.



    A217827E01
  1. Remove the IGCT relay from the engine room junction block assembly.
    Text in Illustration 
    *1
    Engine Room Junction Block Assembly
    *2
    IGCT Relay

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E03
  1. Disconnect only the c1 connector of the battery smart unit.



    A217829E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    IGCT relay terminal 5 - c1-4 (IGCT)
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Battery Smart Unit)
    *2
    Engine Room Junction Block Assembly
    *3
    IGCT relay terminal 5

  1. Connect the c1 connector of the battery smart unit.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Install the IGCT relay to the engine room junction block assembly.

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPAIR POWER SOURCE CIRCUIT