Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > ECO Switch Circuit

for Preparation Click here


DESCRIPTION

The integration control and panel sub-assembly (ECO MODE switch) is installed on the instrument panel on the driver side. When the integration control and panel sub-assembly (ECO MODE switch) is turned on, the A/C amplifier receives an integration control and panel sub-assembly (ECO MODE switch) ON signal and controls the air conditioning to enhance fuel efficiency.
When the heater is on, the engine ON request coolant temperature will be set to a lower level. Thus, the length of time that the engine operates to generate the heat necessary to operate the heater will be limited. When the engine coolant temperature drops, the amount of air flow of the blower motor will also decrease. If FOOT/DEF or DEF is selected, or if the temperature is set to MAX HOT, the fuel efficiency control due to the integration control and panel sub-assembly (ECO MODE switch) operation will be canceled.
When the air conditioning is used to cool the vehicle, the power consumption of the compressor will be limited. Initially, the air conditioning will operate normally until the cabin temperature stabilizes. After the cabin temperature stabilizes, the power consumption of the compressor will be limited while stabilizing the cabin temperature. If the temperature is set to MAX COOL, the fuel efficiency control due to the integration control and panel sub-assembly (ECO MODE switch) operation will be canceled.

WIRING DIAGRAM


E190030E01


INSPECTION PROCEDURE

1.INSPECT AIR CONDITIONING AMPLIFIER


    E124471E97
  1. Remove the A/C amplifier with the connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L17-15 (ECOS) - Body ground
    Power switch on (IG)
    ECO MODE switch off (when switch is not pressed)
    11 to 14 V
    L17-15 (ECOS) - Body ground
    Power switch on (IG)
    ECO MODE switch on (when switch is pressed)
    Below 1 V

    Text in Illustration 
    *1
    Component with harness connected
    (A/C Amplifier)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH - BODY GROUND)


    E167399E24
  1. Disconnect the connector from the integration control and panel sub-assembly (ECO MODE switch).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-5 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Control and Panel Sub-assembly (ECO MODE Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (ECO MODE SWITCH)


    E190031E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-2 (ECU) - L78-5 (E)
    ECO MODE switch off
    (when switch is not pressed)
    10 kΩ or higher
    L78-2 (ECU) - L78-5 (E)
    ECO MODE switch on
    (when switch is pressed)
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Integration Control and Panel Sub-assembly (ECO MODE Switch))



NG
REPLACE INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (ECO MODE SWITCH) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - ECO MODE SWITCH)


    E177002E68
  1. Disconnect the connector from the A/C amplifier.



    E167399E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-15 (ECOS) - L78-2 (ECU)
    Always
    Below 1 Ω
    L17-15 (ECOS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to A/C Amplifier)
    *2
    Front view of wire harness connector
    (to Integration Control and Panel Sub-assembly (ECO MODE Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER (Click here)