Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1100    Lost Communication with Seat Belt Control ECU

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U1100
No communication from the seat belt control ECU continues.
  1. Seat belt control ECU branch wire or connector
  2. Power source circuit of seat belt control ECU
  3. Seat belt control ECU

HINT:
The diagnosis procedure is for when DTC U1100 is output by the power management control ECU (Intelligent tester display: Power Management1).


WIRING DIAGRAM


C210449E03


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

    HINT:
    If CAN No. 2 bus DTC U1002 is output from the power management control ECU (Intelligent tester display/Power Management1), troubleshoot for U1002 and check for malfunctions in the CAN No. 2 main bus circuit.

    Result:
    Result
    Proceed to
    U1002 is not output from power management control ECU (Intelligent tester display/Power Management1)
    A
    U1002 is output from power management control ECU (Intelligent tester display/Power Management1)
    B



B
GO TO CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.CHECK CAN BUS WIRE FOR DISCONNECTION (SEAT BELT CONTROL ECU BRANCH WIRE)
  1. Turn the power switch off.



    C150943E15
  1. Disconnect the seat belt control ECU connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L3-1 (CANH) - L3-2 (CANL)
    Power switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE SEAT BELT CONTROL ECU BRANCH WIRE OR CONNECTOR (SEAT BELT CONTROL ECU BRANCH WIRE)
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
  1. Turn the power switch on (IG).



    C150943E16
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L3-8 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C204469E02
  1. Disconnect the seat belt control ECU connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-8 (PGND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)