Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U0164    Lost Communication with A/C ECU

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U0164
No communication from the air conditioning amplifier continues.
  1. Air conditioning amplifier branch wire or connector
  2. Power source circuit of air conditioning amplifier
  3. Air conditioning amplifier

HINT:
The diagnosis procedure is for when DTC U0164 is output by the power management control ECU (Intelligent tester display: Power Management2).


WIRING DIAGRAM


C204209E09


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

    HINT:
    If power management bus DTC U1002 is output from the power management control ECU (Intelligent tester display/Power Management2), troubleshoot for U1002 and check for malfunctions in the power management main bus circuit.

    Result:
    Result
    Proceed to
    U1002 is not output from power management control ECU (Intelligent tester display/Power Management2)
    A
    U1002 is output from power management control ECU (Intelligent tester display/Power Management2)
    B



B
GO TO CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.CHECK CAN BUS WIRE FOR DISCONNECTION (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
  1. Turn the power switch off.



    C188241E23
  1. Disconnect the air conditioning amplifier connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Conditioning Amplifier)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L17-11 (CANH) - L17-12 (CANL)
    Power switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
  1. Turn the power switch on (IG).



    C188241E24
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L17-1 (IG+) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Conditioning Amplifier)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


4.CHECK FRONT AND SIDE MONITOR SYSTEM (GROUND TERMINAL)


    C188241E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-14 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Conditioning Amplifier)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)