Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Microphone Circuit between Microphone and Navigation Receiver Assembly

for Preparation Click here


DESCRIPTION

This circuit sends a microphone signal from the map light assembly (telephone microphone assembly) to the navigation receiver assembly.
It also supplies power from the navigation receiver assembly to the map light assembly (telephone microphone assembly).

WIRING DIAGRAM


E176570E07


INSPECTION PROCEDURE

1.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    w/o Sliding Roof
    A
    w/ Sliding Roof
    B



B
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)


    E168565E16
  1. Disconnect the L37 navigation receiver assembly connector.



    E187118E01
  1. Disconnect the U3 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L37-5 (SNS2) - U3-2 (SNS2)
    Always
    Below 1 Ω
    L37-17 (MACC) - U3-5 (MACC)
    Always
    Below 1 Ω
    L37-19 (MIN+) - U3-4 (MCO+)
    Always
    Below 1 Ω
    L37-20 (MIN-) - U3-3 (MCO-)
    Always
    Below 1 Ω
    L37-5 (SNS2) - Body ground
    Always
    10 kΩ or higher
    L37-17 (MACC) - Body ground
    Always
    10 kΩ or higher
    L37-19 (MIN+) - Body ground
    Always
    10 kΩ or higher
    L37-20 (MIN-) - Body ground
    Always
    10 kΩ or higher
    L37-18 (SGND) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)
*2
Front view of wire harness connector
(to Map Light Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Disconnect the U3 map light assembly connector.



    E176579E07
  1. Reconnect the L37 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L37-17 (MACC) - Body ground
    Power switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L37-18 (SGND) - Body ground
    Always
    Below 1 Ω
    L37-20 (MIN-) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Component with harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.INSPECT MAP LIGHT ASSEMBLY


    E187117E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U3-2 (SNS2) - U3-3 (MCO-)
    Always
    Below 1 Ω

Text in Illustration 
*1
Component without harness connected
(Map Light Assembly)


NG
Go to step 10
OK


5.INSPECT MAP LIGHT ASSEMBLY
  1. Reconnect the L37 navigation receiver assembly connector.



    E187122E01
  1. Reconnect the U3 map light assembly connector.

  1. Turn the power switch on (ACC).

  1. Connect an oscilloscope to terminals 4 (MCO+) and 3 (MCO-) of the U3 map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is output
    A
    A waveform synchronized with the voice input to the map light assembly is not output
    B

Text in Illustration 
*1
Component with harness connected
(Map Light Assembly)


B
Go to step 10
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)


    E168565E17
  1. Disconnect the L37 navigation receiver assembly connector.



    E187215E01
  1. Disconnect the U13 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L37-5 (SNS2) - U13-3 (SNS2)
    Always
    Below 1 Ω
    L37-17 (MACC) - U13-6 (MACC)
    Always
    Below 1 Ω
    L37-19 (MIN+) - U13-5 (MCO+)
    Always
    Below 1 Ω
    L37-20 (MIN-) - U13-4 (MCO-)
    Always
    Below 1 Ω
    L37-5 (SNS2) - Body ground
    Always
    10 kΩ or higher
    L37-17 (MACC) - Body ground
    Always
    10 kΩ or higher
    L37-19 (MIN+) - Body ground
    Always
    10 kΩ or higher
    L37-20 (MIN-) - Body ground
    Always
    10 kΩ or higher
    L37-18 (SGND) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)
*2
Front view of wire harness connector
(to Map Light Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Disconnect the U13 map light assembly connector.



    E176579E07
  1. Reconnect the L37 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L37-17 (MACC) - Body ground
    Power switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L37-18 (SGND) - Body ground
    Always
    Below 1 Ω
    L37-20 (MIN-) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Component with harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


8.INSPECT MAP LIGHT ASSEMBLY


    E187217E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-3 (SNS2) - U13-4 (MCO-)
    Always
    Below 1 Ω

Text in Illustration 
*1
Component without harness connected
(Map Light Assembly)


NG
Go to step 10
OK


9.INSPECT MAP LIGHT ASSEMBLY
  1. Reconnect the L37 navigation receiver assembly connector.



    E187216E01
  1. Reconnect the U13 map light assembly connector.

  1. Turn the power switch on (ACC).

  1. Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the U13 map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is output
    A
    A waveform synchronized with the voice input to the map light assembly is not output
    B

Text in Illustration 
*1
Component with harness connected
(Map Light Assembly)


B
Go to step 10
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

10.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly.

    HINT:
    1. w/o Sliding Roof (Click here)
    2. w/ Sliding Roof (Click here)

  1. Check if the same malfunction recurs.

    Result:
    Result
    Proceed to
    Malfunction does not recur
    (returns to normal)
    A
    Malfunction recurs
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END