Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Microphone Circuit between Microphone and Navigation Receiver Assembly

for Preparation Click here


DESCRIPTION

  1. The navigation ECU sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the navigation ECU sub-assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation ECU sub-assembly.

WIRING DIAGRAM


E245187E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-4 (MACC) - U3-5 (MACC)
    Always
    Below 1 Ω
    L130-5 (MIN+) - U3-4 (MCO+)
    Always
    Below 1 Ω
    L130-19 (MIN-) - U3-3 (MCO-)
    Always
    Below 1 Ω
    L130-6 (SNS2) - U3-2 (SNS2)
    Always
    Below 1 Ω
    L130-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    L130-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    L130-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-4 (MACC) - U13-6 (MACC)
    Always
    Below 1 Ω
    L130-5 (MIN+) - U13-5 (MCO+)
    Always
    Below 1 Ω
    L130-19 (MIN-) - U13-4 (MCO-)
    Always
    Below 1 Ω
    L130-6 (SNS2) - U13-3 (SNS2)
    Always
    Below 1 Ω
    L130-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    L130-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    L130-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT NAVIGATION ECU SUB-ASSEMBLY
  1. Reconnect the navigation ECU sub-assembly connector.

  1. Reconnect the map light assembly (telephone microphone assembly) connector.



    E237416E06
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L130-4 (MACC) - Body ground
    Power switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L130-18 (SGND) - Body ground
    Always
    Below 1 Ω
    L130-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU Sub-assembly)



NG
Go to step 3
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the map light assembly (telephone microphone assembly) connector.



    E245346E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    U3-2 (SNS2) - U3-3 (MCO-)
    Always
    Below 1 Ω
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    U13-3 (SNS2) - U13-4 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *a
    Component without harness connected
    (Map Light Assembly (Telephone Microphone Assembly))



NG
Go to step 5
OK


4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Reconnect the navigation ECU sub-assembly connector.



    E245347E01
  1. Reconnect the map light assembly (telephone microphone assembly) connector.

  1. Turn the power switch on (ACC).

  1. Connect an oscilloscope to terminals 4 (MCO+) and 3 (MCO-) of the map light assembly (telephone microphone assembly) connector (w/o Sliding Roof).

  1. Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the map light assembly (telephone microphone assembly) connector (w/ Sliding Roof).

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output
    A
    A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output
    B

    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *a
    Component without harness connected
    (Map Light Assembly (Telephone Microphone Assembly))



B
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (w/ Sliding Roof) (Click here).

  1. Replace the telephone microphone assembly (w/o Sliding Roof) (Click here).

  1. Check if the same malfunction recurs.

    Result:
    Result
    Proceed to
    Malfunction does not recur
    (returns to normal)
    A
    Malfunction recurs
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END