NAVIGATION SYSTEM (for Radio and Display Type) > Microphone Circuit between Microphone and Radio Receiver |

| 1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
Disconnect the radio and display receiver assembly connector.
Disconnect the map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L149-6 (SNS2) - U3-2 (SNS2) | Always | Below 1 Ω |
| L149-4 (MACC) - U3-5 (MACC) | Always | Below 1 Ω |
| L149-5 (MIN+) - U3-4 (MCO+) | Always | Below 1 Ω |
| L149-19 (MIN-) - U3-3 (MCO-) | Always | Below 1 Ω |
| L149-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| L149-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| L149-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| L149-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| L149-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| L149-6 (SNS2) - U13-3 (SNS2) | Always | Below 1 Ω |
| L149-4 (MACC) - U13-6 (MACC) | Always | Below 1 Ω |
| L149-5 (MIN+) - U13-5 (MCO+) | Always | Below 1 Ω |
| L149-19 (MIN-) - U13-4 (MCO-) | Always | Below 1 Ω |
| L149-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| L149-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| L149-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| L149-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| L149-18 (SGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
Reconnect the radio and display receiver assembly connector.
Reconnect the map light assembly (telephone microphone assembly) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L149-4 (MACC) - Body ground | Power switch on (ACC) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L149-18 (SGND) - Body ground | Always | Below 1 Ω |
| L149-19 (MIN-) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
|
| ||||
| OK | |
| 3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Disconnect the map light assembly (telephone microphone assembly) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U3-2 (SNS2) - U3-3 (MCO-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| U13-3 (SNS2) - U13-4 (MCO-) | Always | Below 1 Ω |
| *A | w/o Sliding Roof |
| *B | w/ Sliding Roof |
| *a | Component without harness connected (Map Light Assembly (Telephone Microphone Assembly)) |
|
| ||||
| OK | |
| 4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Reconnect the radio and display receiver assembly connector.
Reconnect the map light assembly (telephone microphone assembly) connector.
Turn the power switch on (ACC).
Connect an oscilloscope to terminals 4 (MCO+) and 3 (MCO-) of the map light assembly (telephone microphone assembly) connector (w/o Sliding Roof).
![]() |
Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the map light assembly (telephone microphone assembly) connector (w/ Sliding Roof).
Check the waveform of the telephone microphone assembly using the oscilloscope.
| Result | Proceed to |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output | A |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output | B |
| *A | w/o Sliding Roof |
| *B | w/ Sliding Roof |
| *a | Component with harness connected (Map Light Assembly (Telephone Microphone Assembly)) |
|
| ||||
| A | ||
| ||
| 5.REPLACE TELEPHONE MICROPHONE ASSEMBLY |
Replace the telephone microphone assembly (w/o Sliding Roof) (Click here).
Replace the telephone microphone assembly (w/ Sliding Roof) (Click here).
Check if the same malfunction recurs.
| Result | Proceed to |
| Malfunction does not recur (returns to normal) | A |
| Malfunction recurs | B |
|
| ||||
| A | ||
| ||