Home › Engine / Hybrid System › 2ZR-FXE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL INTAKE MANIFOLD
  1. w/ Stud Bolt:

    1. Using an E6 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

      HINT:
      If a stud bolt is deformed or the threads are damaged, replace the stud bolt.

  1. Install a new No. 1 intake manifold to head gasket to the intake manifold.

  1. Install the intake manifold with the 2 bolts and 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Connect the fuel vapor feed hose and ventilation hose to the intake manifold.

  1. Install a new O-ring to the engine oil level dipstick guide sub-assembly.

  1. Apply a light coat of engine oil to the O-ring.



    A212681E02
  1. Install the engine oil level dipstick guide sub-assembly with the 2 bolts and connect the wire harness clamp.

    Torque:
    Bolt (A):
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }
    Bolt (B):
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the engine oil level dipstick.



    A212682
  1. Connect the 2 wire harness clamps and 3 connectors.



  1. w/o EGR System:



      A290236E01
    1. Install a new gasket to the intake manifold.
      Text in Illustration 
      *a
      Groove
      *b
      Protrusion

      HINT:
      Align the protrusion of the gasket with the groove on the intake manifold.

    2. Install the surge tank cover to the intake manifold with the 2 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    3. Install the wire harness support to the surge tank cover with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    4. Connect the 2 wire harness clamps.



2. INSTALL VACUUM SWITCHING VALVE ASSEMBLY


    A212674
  1. Install the vacuum switching valve assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A212673
  1. Connect the 2 fuel vapor feed hoses and connector to the vacuum switching valve assembly.

  1. Connect the No. 1 vacuum switching valve connector.



3. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR


    A212672
  1. Install the manifold absolute pressure sensor with the bot.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



4. INSTALL EGR PIPE ASSEMBLY (w/ EGR System)


    A212665
  1. Install 2 new gaskets and EGR pipe assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact with the installation surfaces.



    A212664
  1. Install the wire harness support with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A212663
  1. Connect the 2 wire harness clamps.



5. INSTALL THROTTLE BODY ASSEMBLY
(Click here)