Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for RHD)

BRAKE PEDAL (for RHD) > ADJUSTMENT

for Preparation Click here



1. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.

    1. Turn back the carpet.

    2. Turn back the dash silencer from the slit provided on the dash silencer.



    3. C205693E01
    4. Measure the shortest distance between the brake pedal surface and floor panel.
      Text in Illustration 
      *1
      Stop Light Switch Assembly
      *2
      Clevis Lock Nut
      *3
      Floor Panel
      *4
      Brake Pedal Height

      Brake pedal height from floor panel:
      132.6 to 142.6 mm (5.22 to 5.61 in.)

  1. Adjust the brake pedal height.

    1. Remove the stop light switch assembly (Click here).

    2. Loosen the clevis lock nut.

    3. Adjust the brake pedal height by turning the push rod.

    4. Tighten the clevis lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    5. Install and adjust the stop light switch assembly (Click here).



2. INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY


  1. When reusing the brake pedal stroke sensor assembly:

    1. Connect the cable to the negative (-) battery terminal.

      NOTICE:
      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    2. Connect the intelligent tester to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/ TRC / Data List.



    6. C208068
    7. Reading the value of the brake stroke sensor assembly shown in the Data List, turn the brake pedal stroke sensor assembly slowly to the right and left to adjust the output voltage to the standard voltage.

      Standard Voltage:

      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Stroke Sensor
      Stroke sensor /
      min.: 0 V, max.: 5 V
      0.8 to 1.2 V
      -



    8. C219717E02
    9. Tighten the 2 nuts.

      Torque:
      7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

      NOTICE:
      1. Do not depress the brake pedal after turning the power switch on (IG).
      2. Tighten the 2 nuts in the order shown in the illustration.

    10. Turn the power switch off.

    11. Disconnect the intelligent tester.



3. INSPECT BRAKE PEDAL FREE PLAY


    C132708E03
  1. Depress the pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.
    Text in Illustration 
    *1
    Brake Pedal Free Play

    Pedal free play:
    1.0 to 6.0 mm (0.0394 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance . If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.



4. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.

  1. Release the parking brake pedal.

  1. With the power switch on (READY), depress the brake pedal and measure the pedal reserve distance.

    Pedal reserve distance from the floor panel at 196 N (20 kgf, 44.1 lbf):
    More than 82.0 mm (3.23 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).