Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY

FUEL LID LOCK CONTROL CABLE ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. REMOVE FRONT SEAT ASSEMBLY LH (for LHD)

HINT:
Refer to the procedure up to Remove Front Seat Assembly LH (Click here).



7. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    B227761
  1. Disengage the 10 claws and remove the front door scuff plate LH.



8. REMOVE REAR DOOR SCUFF PLATE LH (for LHD)


    B227766
  1. Disengage the 7 claws and remove the rear door scuff plate LH.



9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    B227770
  1. Remove the rear door opening trim weatherstrip LH.



10. REMOVE LAP BELT OUTER ANCHOR COVER LH (for LHD)


    B221487
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (for LHD)


    B221489
  1. Remove the bolt and disconnect the floor end of the front seat outer belt assembly.



12. REMOVE CENTER PILLAR LOWER GARNISH LH (for LHD)


    B227782
  1. Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish LH.



13. REMOVE FRONT SEAT ASSEMBLY RH (for RHD)

HINT:
Use the same procedure described for the LH side.



14. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure described for the LH side.



15. REMOVE REAR DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure described for the LH side.



16. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

HINT:
Use the same procedure described for the LH side.



17. REMOVE LAP BELT OUTER ANCHOR COVER RH (for RHD)

HINT:
Use the same procedure described for the LH side.



18. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)

HINT:
Use the same procedure described for the LH side.



19. REMOVE CENTER PILLAR LOWER GARNISH RH (for RHD)

HINT:
Use the same procedure described for the LH side.



20. REMOVE REAR SEAT CUSHION ASSEMBLY


    B229992E01
  1. Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Hook
    *3
    Guide

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the above procedure for the other hook.

  1. Disengage the 2 guides of the seat cushion from the seatback.

  1. Remove the rear seat cushion assembly.



21. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    B230041
  1. Remove the bolt.



    B230042
  1. Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.



22. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



23. REMOVE REAR NO. 4 FLOOR BOARD


    B227789
  1. Disengage the guide and remove the rear No. 4 floor board.



24. REMOVE DECK FLOOR BOX LH


    B227790
  1. Remove the clip.

  1. Disengage the 2 guides and remove the deck floor box LH.



25. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



26. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



27. REMOVE REAR NO. 1 FLOOR BOARD


    B227794
  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



28. REMOVE DECK TRIM SERVICE HOLE COVER


    B227795
  1. Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.



29. REMOVE REAR DECK TRIM COVER


    B227796
  1. Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.



30. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


    B227798
  1. Remove the 2 bolts.

  1. Disengage each guide and remove the 2 luggage hold belt striker assemblies.



31. REMOVE TONNEAU COVER HOLDER CAP


    B227799E01
  1. Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



32. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the screw.

  1. Disengage the 7 claws and 2 clips.



  1. Disconnect the connector and remove the deck trim side panel assembly LH.


    B227804



33. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for LHD)


    B227923
  1. Remove the screw.

  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B227925
  1. Disconnect the fuel lid lock control cable sub-assembly.



34. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


    B227918
  1. Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.



  1. Disengage the 7 clamps and remove the fuel lid lock control cable sub-assembly.


    B227927



35. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)


    B227921
  1. Remove the screw.

  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B227920
  1. Disconnect the fuel lid lock control cable sub-assembly.



36. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


    B227918
  1. Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.



  1. Disengage the 12 clamps and remove the fuel lid lock control cable sub-assembly.


    B227926