ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Unlock Function does not Operate |

| 1.CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Door Lock Pos*1 | Front right side lock position switch signal/LOCK or UNLOCK | LOCK: Front right side door locked UNLOCK: Front right side door unlocked | - |
| FL Door Lock Pos*2 | Front left side door lock position switch signal/LOCK or UNLOCK | LOCK: Front left side door locked UNLOCK: Front left side door unlocked | - |
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (DOOR OUTSIDE HANDLE) |
Enter the following menus: Body / Entry & Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D-Door Touch Sensor | Status of touch sensor (for driver side) / ON or OFF | ON: Touch sensor touched OFF: Touch sensor not touched | - |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the certification ECU (smart key ECU assembly) connector.
![]() |
Disconnect the front door outside handle assembly (for driver side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L62-20 (SEN1) - z3-4 (SENS) | Always | Below 1 Ω |
| L62-20 (SEN1) - Body ground | Always | 10 kΩ or higher |
| z3-4 (SENS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| L62-20 (SEN1) - z4-4 (SENS) | Always | Below 1 Ω |
| L62-20 (SEN1) - Body ground | Always | 10 kΩ or higher |
| z4-4 (SENS) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
| *2 | Front view of wire harness connector (to Front Door Outside Handle Assembly (for Driver Side)) |
| *3 | for LHD |
| *4 | for RHD |
|
| ||||
| OK | |
| 5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TOUCH SENSOR SIGNAL INPUT) |
Reconnect the certification ECU (smart key ECU assembly) connector.
Reconnect the front door outside handle assembly (for driver side) connector.

Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L62-20 (SEN1) - L62-15 (E) |
| Pulse generation |
| L62-20 (SEN1) - L62-15 (E) |
| Below 2 V |
| *1 | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) | *2 | for LHD |
| *3 | for RHD | - | - |
|
| ||||
| OK | ||
| ||